Effect of steam bluing process on hexavalent chromium conversion of magnesium chromate coating on non-oriented electrical steel

摘 要
针对无取向电工钢经蒸汽发蓝处理后,其铬酸镁涂层中出现六价铬含量超标的问题,利用紫外可见光分光光度计和气氛热处理等方法研究了不同气氛下发蓝工艺对无取向电工钢涂层中六价铬含量的影响。结果表明:在N2气氛及还原性气氛条件下,随着发蓝时间的延长和温度的升高,涂层中六价铬的含量均会降低,但在较低的发蓝温度下,涂层六价铬的含量下降不明显;要彻底解决六价铬含量超标的问题,必须确保涂层烘烤固化后,材料的六价铬含量达标。








Abstract
Aiming at the problem that the content of hexavalent chromium in the magnesium chromate coating of non-oriented electrical steel after steam bluing treatment exceeded the standard, the effects of bluing process on the content of hexavalent chromium in the coating of non-oriented electrical steel under different atmospheres were studied by means of ultraviolet-visible spectrophotometer and atmosphere heat treatment. The results show that under the condition of N2 atmosphere and reducing atmosphere, the content of hexavalent chromium in the coating would decrease with the extension of blueing time and the increase of temperature. However, the content of hexavalent chromium in the coating did not decrease significantly at lower blueing temperature. In order to completely solve the problem of excessive hexavalent chromium content, it was necessary to ensure that the hexavalent chromium content of the coating reached the standard after baking and curing.
中图分类号 TB31 DOI 10.11973/lhjy-wl202308001
所属栏目 试验与研究
基金项目
收稿日期 2023/6/14
修改稿日期
网络出版日期

作者单位点击查看

备注黄飞(1986-),男,高级工程师,主要从事金属材料质量检验检测工作,283217551@qq.com
引用该论文: HUANG Fei,WANG Yongqiang. Effect of steam bluing process on hexavalent chromium conversion of magnesium chromate coating on non-oriented electrical steel[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2023, 59(8): 1~4
黄飞,王永强. 蒸汽发蓝工艺对无取向电工钢铬酸镁涂层六价铬转化的影响[J]. 理化检验-物理分册, 2023, 59(8): 1~4
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好






参考文献
【1】陈可来.电机冷轧硅钢片退火工艺浅析[J].中小型电机,2004,31(3):49-57.
【2】张鸣元.压缩机电机硅钢片热处理[J].微电机,2005,38(1):67-71.
【3】左宏莲,谢世海,胡克进.耐氟电机硅钢片蒸汽发蓝节能探索[J].金属热处理,2007,32(6):116-117.
【4】葛瑞荣, 周尚荣, 刘诚,等.45钢蒸汽发蓝工艺及膜层性能研究[J]. 材料热处理技术, 2010, 39(10): 94-98.
【5】何忠治.电工钢[M].北京:冶金工业出版社,1997.
【6】顾宝珊,弋慧丽,杨培燕,等.无铬无取向硅钢涂层烧结固化工艺[J].材料热处理学报,2013,34(12):176-182.
【7】贾成义,宁双茂,姜世勇.涂层种类对无取向电工钢消除应力退火后组织性能的影响[J].电工材料,2012(1):34-37.
【8】王立涛,施立发,朱国辉,等.硅钢热处理过程涂层中铬的转化试验研究[J].金属功能材料,2017,24(3):39-44.
【9】李邦波,宋博.硅钢涂层过程中六价铬向三价铬转化测试[J].金属世界,2019(4):43-44.
【10】张大威,孙凯,刘兆光,等.铬酸酐热分解法制取三氧化二铬的烧结研究[J].化工科技市场,2007,30(6):42-44.
【2】张鸣元.压缩机电机硅钢片热处理[J].微电机,2005,38(1):67-71.
【3】左宏莲,谢世海,胡克进.耐氟电机硅钢片蒸汽发蓝节能探索[J].金属热处理,2007,32(6):116-117.
【4】葛瑞荣, 周尚荣, 刘诚,等.45钢蒸汽发蓝工艺及膜层性能研究[J]. 材料热处理技术, 2010, 39(10): 94-98.
【5】何忠治.电工钢[M].北京:冶金工业出版社,1997.
【6】顾宝珊,弋慧丽,杨培燕,等.无铬无取向硅钢涂层烧结固化工艺[J].材料热处理学报,2013,34(12):176-182.
【7】贾成义,宁双茂,姜世勇.涂层种类对无取向电工钢消除应力退火后组织性能的影响[J].电工材料,2012(1):34-37.
【8】王立涛,施立发,朱国辉,等.硅钢热处理过程涂层中铬的转化试验研究[J].金属功能材料,2017,24(3):39-44.
【9】李邦波,宋博.硅钢涂层过程中六价铬向三价铬转化测试[J].金属世界,2019(4):43-44.
【10】张大威,孙凯,刘兆光,等.铬酸酐热分解法制取三氧化二铬的烧结研究[J].化工科技市场,2007,30(6):42-44.
相关信息