Continuous Cooling Transformation Curve of BM510L Steel for Automobile Frames
摘 要
采用膨胀法在Gleeble-3500型热模拟试验机上测定了BM510L钢在不同冷速下连续冷却时的膨胀曲线及连续冷却转变曲线(CCT曲线); 利用光学显微镜、显微硬度计研究了BM510L钢连续冷却过程中奥氏体转变后的组织和显微硬度。结果表明: 随着冷速的提高, 铁素体转变开始温度降低, 珠光体转变终了温度也逐渐降低, 当冷速大于1 ℃·s-1时, 组织中开始发生贝氏体转变, 当冷速为15 ℃·s-1时, 组织已完全转变为贝氏体组织; 随着冷速的提高, 其显微硬度逐渐增大。
Abstract
The dilatometric curves and continuous cooling transformation (CCT) curves of BM510L steel at different cooling rates were measured in Gleeble-3500 thermal simulating test machine by dilatometric measurement. The microstructure and microhardness of BM510L steel after transformation of austenite in continuous cooling process were studied by optical microscopy (OM) and microhardness tester. The results show that as the cooling rate increases, both the initiate temperature of ferrite transformation and the terminal temperature of pearlite transformation decrease. The bainite is obtained in the microstructure at the cooling rate above 1 ℃·s-1, and the microstructure is totally bainite at the cooling rate of 15 ℃·s-1. The hardness increases with the increase of cooling rate.
中图分类号 TG115
所属栏目 试验研究
基金项目
收稿日期 2013/3/12
修改稿日期 2014/3/1
网络出版日期
作者单位点击查看
备注赵楠(1977-), 女, 山东诸城人, 工程师, 硕士。
引用该论文: ZHAO Nan,ZHOU Li-ping,HUANG Xu-chuan,MU Hai-ling. Continuous Cooling Transformation Curve of BM510L Steel for Automobile Frames[J]. Materials for mechancial engineering, 2014, 38(6): 38~40
赵楠,周丽萍,黄绪传,穆海玲. BM510L汽车大梁钢的连续冷却转变曲线[J]. 机械工程材料, 2014, 38(6): 38~40
被引情况:
【1】靳永明,张宜生,梁卫抗,郑徐雨,李阳, "加热速率对22MnB5超高强度钢奥氏体化的影响",机械工程材料 40, 80-83(2016)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】万兰凤, 冷祥贵.铌钛微合金化汽车大梁钢BM510L的开发[J].梅山科技, 2005(1): 27-29.
【2】尹环泽.16MnL汽车大梁钢板的开发与试制[J].轧钢, 2005(1): 64-66.
【3】向浪涛, 黄艳, 张增枢.热轧汽车大梁钢510L的研制[J].重钢技术, 2002(1): 25-27.
【4】赵楠, 穆海玲, 周丽萍, 等.BM510汽车大梁钢冷弯开裂原因分析[J].机械工程材料, 2008, 32(11): 72-74.
【5】YB/T 5127-93钢的临界点测定方法(膨胀法)[S].
【6】YB/T 5129-93钢的连续冷却转变曲线图的测定方法(膨胀法)[S].
【7】李红英, 龚美涛, 何堃.77B奥氏体连续冷却转变曲线(CCT图)[J].热加工工艺, 2005(4): 58-59.
【8】王佳夫, 林清华, 漆世泽, 等.冷却速度对高强度低合金钢组织和性能的影响[J].钢铁研究学报, 2004, 16(5): 51-55.
【2】尹环泽.16MnL汽车大梁钢板的开发与试制[J].轧钢, 2005(1): 64-66.
【3】向浪涛, 黄艳, 张增枢.热轧汽车大梁钢510L的研制[J].重钢技术, 2002(1): 25-27.
【4】赵楠, 穆海玲, 周丽萍, 等.BM510汽车大梁钢冷弯开裂原因分析[J].机械工程材料, 2008, 32(11): 72-74.
【5】YB/T 5127-93钢的临界点测定方法(膨胀法)[S].
【6】YB/T 5129-93钢的连续冷却转变曲线图的测定方法(膨胀法)[S].
【7】李红英, 龚美涛, 何堃.77B奥氏体连续冷却转变曲线(CCT图)[J].热加工工艺, 2005(4): 58-59.
【8】王佳夫, 林清华, 漆世泽, 等.冷却速度对高强度低合金钢组织和性能的影响[J].钢铁研究学报, 2004, 16(5): 51-55.
相关信息