Process of Chrome-free Chemical Conversion Film on Aluminum Alloy
摘 要
采用单因素试验方法,以磷酸盐化学转化膜膜重及其在3.5% NaCl溶液经全浸腐蚀试验的失重率作为转化膜性能评价指标,确定了以Y2O3为添加剂的铝合金磷酸盐化学转化处理液的最佳配方和工艺参数: ZnO 8 g/L,H3PO4 20 mL/L,NaF 0.8 g/L,Y2O3 0.02 g/L,处理温度为(40±2) ℃,处理时间为8~10 min,pH=(3.0±2)。采用模拟大气腐蚀及全浸泡试验研究了经不同转化处理的铝合金试样涂漆后转化膜与涂层间的结合力。结果表明,在相同的试验条件下,稀土促进生成的磷酸盐化学转化膜与有机涂层间的结合力优于磷酸-铬酸盐转化膜。
Abstract
Take the weight of phosphate conversion coating and the rate of weight loss in 3.5% NaCl solution as evaluation indexes, orthogonal experiment was used to determine the optimal formula and technological parameters of phosphate conversion processing solution with Y2O3 as additive. The parameters are as follows: ZnO 8 g/L, H2PO3 20 mL/L, NaF 0.8 g/L, Y2O3 0.02 g/L, temperature = (40±2) ℃, time=8-10 min, pH = (3.0±2). The phosphate conversion films formed under the technological conditions has good corrosion resistance. The binding force between the conversion films which were differently processed on aluminum alloy samples after painting and the organic coating was studied by simulated atmospheric corrosion and full immersion test. The results show that under the same experimental conditions, the bonding force between the phosphate conversion film generated with Y2O3 as additive and the organic coating is superior to that of phosphate-chromate conversion film.
中图分类号 TG174
所属栏目 应用技术
基金项目 河南省科技攻关重点项目(122102310321)
收稿日期 2013/4/28
修改稿日期
网络出版日期
作者单位点击查看
备注李红玲(1977-),讲师,硕士,从事金属材料表面改性研究,
引用该论文: LI Hong-ling. Process of Chrome-free Chemical Conversion Film on Aluminum Alloy[J]. Corrosion & Protection, 2014, 35(2): 169
被引情况:
【1】刘迎新,余取民,王开丽, "免水洗常温锰系磷化膜的制备与性能",腐蚀与防护 36, 1153-1155(2015)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】间宫富士雄著,刘俊哲译. 金属的化学处理[M]. 北京:化学工业出版社,1987.
【2】周谟银. 影响铝合金磷化膜单位重量的因素[J]. 材料保护,1997,30(4):34-36.
【3】周谟银. 游离F-和氧化剂对铝镁合金(LF2)磷化过程的影响[J]. 材料保护,1998,31(7):13-16.
【4】汪泉发. 金属磷化技术[J]. 电镀与环保,1994,14(4):17-19.
【5】张学敏. 涂装工艺学[M]. 北京:化学工业出版社,2002.
【6】雷作缄,胡梦珍编译. 金属磷化处理[M]. 北京:机械工业出版社,1992.
【7】曹鹏军,仟海东.范培耕,等. 铝合金的转化膜处理工艺研究[J]. 表面技术,2003,32(2):44-47.
【8】汪泉发,黎燕. 铝及其合金化学转化膜技术[J]. 电镀与环保,1993,13(4):11-14.
【9】周谟银. 铝材的锌系磷化(1):锌系磷化对铝材涂装的意义[J]. 上海电镀,1998,1(2):2-4.
【2】周谟银. 影响铝合金磷化膜单位重量的因素[J]. 材料保护,1997,30(4):34-36.
【3】周谟银. 游离F-和氧化剂对铝镁合金(LF2)磷化过程的影响[J]. 材料保护,1998,31(7):13-16.
【4】汪泉发. 金属磷化技术[J]. 电镀与环保,1994,14(4):17-19.
【5】张学敏. 涂装工艺学[M]. 北京:化学工业出版社,2002.
【6】雷作缄,胡梦珍编译. 金属磷化处理[M]. 北京:机械工业出版社,1992.
【7】曹鹏军,仟海东.范培耕,等. 铝合金的转化膜处理工艺研究[J]. 表面技术,2003,32(2):44-47.
【8】汪泉发,黎燕. 铝及其合金化学转化膜技术[J]. 电镀与环保,1993,13(4):11-14.
【9】周谟银. 铝材的锌系磷化(1):锌系磷化对铝材涂装的意义[J]. 上海电镀,1998,1(2):2-4.
相关信息