Influence of Heat Treatment Process on Performance of Boundary Layer of Copper Clad Aluminum Compound Bus Bar
摘 要
使用五机架连轧工艺制备了铜铝复合母线排, 通过不同热处理工艺对轧态产品进行处理, 使用光学显微镜观察了铜铝界面层的形貌, 使用显微硬度计测试了界面层的硬度分布, 使用能谱对界面处的成分变化进行了分析。结果表明: 温度对界面合金化层的影响作用较大; 冷却方式对复合母排的力学性能影响较小, 复合母排的表面布氏硬度低于铜层的硬度。
Abstract
Copper clad aluminum bus bar was prepared using five stand continuous rolling system and heat-treated by different processes, the Cu/Al boundary layer was observed using optical microscope, and hardness of the boundary was tested using micro-hardness tester, the chemical composition was tested using EDX. The results showed that cooling process played less impact on the performance of boundary layer, but temperature had a bigger impact. And Brinell hardness on the surface of bus bar was lower than that of copper layer.
中图分类号 TM244+.3
所属栏目 试验与研究
基金项目
收稿日期 2013/5/17
修改稿日期
网络出版日期
作者单位点击查看
备注马力(1982-), 男, 工程师, 工学学士。
引用该论文: MA Li,ZHANG Quan-cheng,LIU Na. Influence of Heat Treatment Process on Performance of Boundary Layer of Copper Clad Aluminum Compound Bus Bar[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2014, 50(1): 11~13
马力,张全成,刘娜. 热处理工艺对铜铝复合母线排界面性能的影响[J]. 理化检验-物理分册, 2014, 50(1): 11~13
被引情况:
【1】姚 强,朱宇宏,王 燕,路 通,王 琼, "GB/T 32496-2016《金属基复合材料增强体体积含量试验方法 图像分析法》标准解析",理化检验-物理分册 52, 621-624(2016)
【2】张全成,马力, "输变电设备用铜铝复合母线研究现状与发展",理化检验-物理分册 51, 416-420(2015)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】孙德勤,吴春京,谢建新.铜包铝复合线材制作技术的发展现状与前景[J].电线电缆,2003(3):3-6.
【2】高文浩.铜包铝线标准化[J].光纤与电缆及其应用技术,1999(3):23-27.
【3】刘芳.金属的电化学腐蚀与铜铝导体的连接[J].农村电气化,2001(3):35-36.
【4】张正南.跌层母线排[J].电源技术应用,2001(3):35-36.
【5】周邦新,蒋有荣.Cu-Al爆炸焊接结合层的透射电镜研究[J].金属学报,1994(3):104-108.
【6】戴雅康.铜包铝内导体CATV同轴电缆的特性[J].广播与电视技术,1997(5):25-28.
【2】高文浩.铜包铝线标准化[J].光纤与电缆及其应用技术,1999(3):23-27.
【3】刘芳.金属的电化学腐蚀与铜铝导体的连接[J].农村电气化,2001(3):35-36.
【4】张正南.跌层母线排[J].电源技术应用,2001(3):35-36.
【5】周邦新,蒋有荣.Cu-Al爆炸焊接结合层的透射电镜研究[J].金属学报,1994(3):104-108.
【6】戴雅康.铜包铝内导体CATV同轴电缆的特性[J].广播与电视技术,1997(5):25-28.
相关信息