Reason Analysis on Lower Detection Value of Surface Rockwell Hardness of Home Appliance Plate JD1
摘 要
家电板JD1的表面洛氏硬度测试结果偏低, 通过对比研究提出了改进措施, 更换了压头球, 优化了硬度计内部参数等。通过试验验证了改进措施效果较好, 最终得到了符合标准和用户要求的表面洛氏硬度测试结果。
Abstract
The detection values of surface Rockwell hardness of home appliance plate JD1 were lower. The improvement measures were put forward by compare and research, including pressure head replacement, internal parameters optimization for hardness tester and so on. The experiment results verified that the improvement effect was good, the hardness detection results met the requirements of standard and user.
中图分类号 TG113.25+1
所属栏目 试验技术与方法
基金项目
收稿日期 2013/7/31
修改稿日期
网络出版日期
作者单位点击查看
备注李智博(1965-), 男, 高级工程师, 学士。
引用该论文: LI Zhi-bo. Reason Analysis on Lower Detection Value of Surface Rockwell Hardness of Home Appliance Plate JD1[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2014, 50(7): 490~491
李智博. 家电板JD1表面洛氏硬度测试值偏低的原因分析[J]. 理化检验-物理分册, 2014, 50(7): 490~491
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】许拴柱, 贾砚生.影响马口铁表面洛氏硬度测定值的几个因素[J].理化检验-物理分册, 1996, 32(1):45.
【2】邱南曦.影响马口铁表面洛氏硬度测定值的因素[J].科学技术与工程, 2007, 2(3):377-380.
【3】李晓东.洛氏硬度试验结果的影响因素[J].理化检验-物理分册, 2010, 46(4):274-276.
【4】李久林.圆柱形试样洛氏硬度值的修正[J].冶金分析与测试(冶金物理测试分册), 1984(6):62-65.
【5】何文喜, 齐之利, 霍建华.洛氏硬度实验的误差分析[J].天津冶金, 2008(3):63-64.
【2】邱南曦.影响马口铁表面洛氏硬度测定值的因素[J].科学技术与工程, 2007, 2(3):377-380.
【3】李晓东.洛氏硬度试验结果的影响因素[J].理化检验-物理分册, 2010, 46(4):274-276.
【4】李久林.圆柱形试样洛氏硬度值的修正[J].冶金分析与测试(冶金物理测试分册), 1984(6):62-65.
【5】何文喜, 齐之利, 霍建华.洛氏硬度实验的误差分析[J].天津冶金, 2008(3):63-64.
相关信息