Preventing High Strength Casing from Fracture and Standardization
摘 要
通过对高强度套管断裂原因进行大量调查研究和失效分析, 认为套管材料钢级越高, 需要匹配的韧性也越高, 高强度(屈服强度≥140 ksi,即965 MPa)套管断裂原因主要与材料强度和韧性不匹配有关。要从根本上解决高强度套管断裂问题, 首先应当对高强度套管断裂原因进行失效分析和研究, 找出其断裂原因;然后依据失效分析和研究成果制定严格的订货技术标准, 并采取一定的措施落实订货技术标准。
Abstract
By a large number of investigation and failure analysis on fracture failure of high strength casings(yield strength≥140 ksi or 965 MPa), it was considered that the higher strength grade of the casing was, the more toughness required for the casing material was. The high strength casing fracture was mainly related to their low toughness that was not satisfied with its strength. In order to solve radically high strength casing fracture problem, casing fracture failure analysis and research should be done first to find out the fracture causes, and then technical standard should be established in accordance with failure analysis and research results, and some measures should be taken to carry out the technical standard.
中图分类号 TE973
所属栏目 实践经验
基金项目
收稿日期 2013/10/20
修改稿日期
网络出版日期
作者单位点击查看
备注李中全(1972-),男,汉族,工程师。
引用该论文: LI Zhong-quan,Lv Shuan-lu,YANG Cheng-xin,LI Ning,YU Ying-ying,SHI Gui-jun,FAN Wen-gang,ZHU Jian-fei. Preventing High Strength Casing from Fracture and Standardization[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2014, 50(12): 903~906
李中全,吕拴录,杨成新,李宁,俞莹滢,石桂军,樊文刚,朱剑飞. 高强度套管断裂失效预防及标准化[J]. 理化检验-物理分册, 2014, 50(12): 903~906
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】吕拴录, 李鹤林. V150套管接箍破裂原因分析[J]. 理化检验-物理分册,2005, 41(增1): 285-290.
【2】吕拴录, 康延军, 刘胜, 等. 井口套管裂纹原因分析[J]. 石油钻探技术, 2009, 37(5): 85-88.
【3】吕拴录,骆发前,康延军. 273.05 mm套管裂纹原因分析[J]. 钢管, 2010(增刊): 22-25.
【4】吕拴录, 康延军, 刘胜, 等. 井口套管裂纹原因分析[J]. 石油钻探技术, 2009, 37(5): 85-88.
【5】许峰, 吕拴录, 康延军, 等. 井口套管磨损失效原因分析及预防措施研究[J]. 石油钻采工艺, 2011, 33(2): 140-142.
【6】滕学清,吕拴录,丁毅,等. 140 ksi高强度套管外螺纹接头裂纹原因分析[J]. 物理测试, 2012, 30(2):59-62.
【7】许峰, 吕拴录, 康延军, 等. 井口套管磨损失效原因分析及预防措施研究[J]. 石油钻采工艺, 2011, 33(2): 140-142.
【8】刘德英,吕拴录,丁毅,等. 塔里木油田套管粘扣预防及标准化[J]. 理化检验-物理分册, 2012,48(11):773-775.
【9】腾学清, 吕拴录, 宋周成, 等. 某井特殊螺纹套管粘扣和脱扣原因分析[J]. 理化检验-物理分册,2011,47(4): 261-264.
【2】吕拴录, 康延军, 刘胜, 等. 井口套管裂纹原因分析[J]. 石油钻探技术, 2009, 37(5): 85-88.
【3】吕拴录,骆发前,康延军. 273.05 mm套管裂纹原因分析[J]. 钢管, 2010(增刊): 22-25.
【4】吕拴录, 康延军, 刘胜, 等. 井口套管裂纹原因分析[J]. 石油钻探技术, 2009, 37(5): 85-88.
【5】许峰, 吕拴录, 康延军, 等. 井口套管磨损失效原因分析及预防措施研究[J]. 石油钻采工艺, 2011, 33(2): 140-142.
【6】滕学清,吕拴录,丁毅,等. 140 ksi高强度套管外螺纹接头裂纹原因分析[J]. 物理测试, 2012, 30(2):59-62.
【7】许峰, 吕拴录, 康延军, 等. 井口套管磨损失效原因分析及预防措施研究[J]. 石油钻采工艺, 2011, 33(2): 140-142.
【8】刘德英,吕拴录,丁毅,等. 塔里木油田套管粘扣预防及标准化[J]. 理化检验-物理分册, 2012,48(11):773-775.
【9】腾学清, 吕拴录, 宋周成, 等. 某井特殊螺纹套管粘扣和脱扣原因分析[J]. 理化检验-物理分册,2011,47(4): 261-264.
相关信息