Terahertz Nondestructive Inspection for Adhesive Face with Composite Materials and Steel Plate
摘 要
在分析了太赫兹无损检测技术工作原理的基础上,应用德国SynViewScan 300连续太赫兹成像系统对复合材料与钢板黏合面进行了检测,研究了太赫兹无损检测技术对黏合面质量的检测能力。试验结果表明,太赫兹波能透过复合材料,获得样件与钢板黏合面的二维太赫兹图像,并能据此评估黏合质量,满足其无损检测的要求。研究结果为复合材料黏合质量及脱黏状况的测试提供了有力的技术支持。
Abstract
Based on the analysis of terahertz nondestructive inspection technology, the adhesive faces with composite materials and steel plate were tested with Germany SynViewScan 300 consecutive terahertz imaging system, and the feasibility of terahertz nondestructive inspection technique for adhesive quality was studied. The results showed that terahertz wave could pass through the composite materials, the adhesive quality of sample and sheet plate was estimated with the two-dimension terahertz imaging of adhesive face, and the requirements of nondestructive inspection were satisfied. The studies provided strong technical support for composite materials adhesive quality and off sticky situation test.
中图分类号 TG115.28
所属栏目 试验研究
基金项目 湖北省自然科学基金资助项目(2012FFA074);校自主创新研究基金资助项目(2012QN094,2012QN097)
收稿日期 2013/8/26
修改稿日期
网络出版日期
作者单位点击查看
备注杨振刚(1979-),男,博士,讲师,主要从事太赫兹光电子学方面的研究。
引用该论文: YANG Zhen-gang,LIU Jin-song,WANG Ke-jia. Terahertz Nondestructive Inspection for Adhesive Face with Composite Materials and Steel Plate[J]. Nondestructive Testing, 2014, 36(4): 42~44
杨振刚,刘劲松,王可嘉. 复合材料与钢板黏合面的太赫兹无损检测[J]. 无损检测, 2014, 36(4): 42~44
被引情况:
【1】董方旭,王从科,凡丽梅,赵付宝,李金鹿,张霞,郑素萍, "X射线检测技术在复合材料检测中的应用与发展",无损检测 38, 67-72(2016)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】傅天航,刘松平.浅谈复合材料超声手动扫描成像检测[J].无损检测,2012,34(8):50-54.
【2】温茂萍,田勇,游开兴.复合构件粘合质量超声多次脉冲反射检测方法[J].测量技术学报,1996,10(2/3):679-682.
【3】许景周,张希成.太赫兹科学技术和应用[M].北京:北京大学出版社,2007.
【4】杨振刚,刘劲松,王可嘉.连续太赫兹成像系统对多层蜂窝样件无损检测的试验研究[J].光电子.激光,2013,24(6):1158-1162.
【2】温茂萍,田勇,游开兴.复合构件粘合质量超声多次脉冲反射检测方法[J].测量技术学报,1996,10(2/3):679-682.
【3】许景周,张希成.太赫兹科学技术和应用[M].北京:北京大学出版社,2007.
【4】杨振刚,刘劲松,王可嘉.连续太赫兹成像系统对多层蜂窝样件无损检测的试验研究[J].光电子.激光,2013,24(6):1158-1162.
相关信息