Effect of Anodizing on Weather Resistance of Aluminum Foil Mesh Conducting Layer Composite
摘 要
采用磷酸阳极氧化处理工艺对铝箔网进行了处理, 对铝箔网的表面形貌进行了分析, 并分析了复合材料铝箔网导电层的耐候性能, 包括耐海水腐蚀、耐冷热疲劳及热氧老化性能。结果表明, 磷酸阳极氧化处理后, 铝箔网表面生成了一层疏松多孔的阳极氧化膜, 可以增大铝箔网表面与复合材料的粘接界面面积, 复合材料铝箔网导电层粘接副的抗拉剪强度随海水腐蚀时间、冷热疲劳次数以及热氧腐蚀时间的增加而下降。相对于未进行磷酸阳极氧化处理的铝箔网, 磷酸阳极氧化处理复合材料铝箔网导电层具有良好的耐候性能。
Abstract
The aluminum foil mesh samples were anodized in phosphoric acid solutions. The surface microstructure of aluminum foil mesh samples was observed and analyzed. The weather resistance of aluminum foil mesh conducting layer composite was analyzed, including seawater resistance, thermal fatigue resistance and thermal-oxidative aging. The results showed that a porous film was formed on the surface of the anodized foil mesh, and the bonding interface area of aluminum foil mesh and composite material increased. With the increase of seawater corrsion time, thermal fatigue resistance time and thermal-oxidative aging time, the shear strength of double-bonding of aluminum foil mesh conducting layer composite decreased. The anodized aluminum foil mesh had good weather resistance than the non-anodized one.
中图分类号 TG174.45
所属栏目 试验研究
基金项目 中国民航大学科研基金资助项目(2010kys05)
收稿日期 2011/3/31
修改稿日期 2011/6/9
网络出版日期
作者单位点击查看
联系人作者李娜(n-li@cauc.edu.cn)
备注李娜, 实验师,
引用该论文: LI Na,JI Zhao-hui,JIA Peng. Effect of Anodizing on Weather Resistance of Aluminum Foil Mesh Conducting Layer Composite[J]. Corrosion & Protection, 2011, 32(11): 872
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】颜鸣皋, 吴学仁, 朱知寿, 等. 航空材料技术的发展现状与展望[J]. 航空制造技术, 2003(12):19-25.
【2】沈军, 谢怀勤. 先进复合材料在航空航天领域的研发与应用[J]. 材料科学与工艺, 2008, 16(5):737-740.
【3】杨乃宾. 复合材料飞机结构设计[M]. 北京:航空工业出版社, 2002.
【4】邵箭, 朱承斌. 飞机设计手册[M]. 北京:航空工业出版社, 1996.
【5】陈志. 火焰铝喷涂技术在碳纤维/复合材料飞机制件上的应用[J]. 表面技术, 1998, 27(5):31-33.
【6】李其连, 李淑青, 杨伟华. 转移法火焰喷涂静电屏蔽涂层[J]. 材料保护, 2007, 40(1):19-21.
【7】Astrid B. Anodising as pre-treatment for structural bonding[J]. International Journal of Adhesion & Adhesives, 2003(23):401-412.
【8】朱祖芳. 铝合金阳极氧化与表面处理技术[M]. 北京:化学工业出版社, 2004.
【9】钱苗根. 现代表面技术[M]. 北京:机械工业出版社, 2004.
【10】杨孚标, 肖加余, 曾竟成, 等. 铝合金磷酸阳极氧化和胶接性能分析[J]. 中国表面工程, 2005, 18(4):37-40.
【11】Lu Y, Wu F, Xue G, et al. Interfacial modification for an aluminum/ epoxy resin laminated composite[J]. Composite Interface, 1994, 2(4):265-269.
【12】杜先智, 丁明桐, 丁秀芬. 新型铝合金阳极氧化膜的机械特性和组织结构[J]. 安徽师大学报(自然科学版), 1997, 20(1):59-61.
【2】沈军, 谢怀勤. 先进复合材料在航空航天领域的研发与应用[J]. 材料科学与工艺, 2008, 16(5):737-740.
【3】杨乃宾. 复合材料飞机结构设计[M]. 北京:航空工业出版社, 2002.
【4】邵箭, 朱承斌. 飞机设计手册[M]. 北京:航空工业出版社, 1996.
【5】陈志. 火焰铝喷涂技术在碳纤维/复合材料飞机制件上的应用[J]. 表面技术, 1998, 27(5):31-33.
【6】李其连, 李淑青, 杨伟华. 转移法火焰喷涂静电屏蔽涂层[J]. 材料保护, 2007, 40(1):19-21.
【7】Astrid B. Anodising as pre-treatment for structural bonding[J]. International Journal of Adhesion & Adhesives, 2003(23):401-412.
【8】朱祖芳. 铝合金阳极氧化与表面处理技术[M]. 北京:化学工业出版社, 2004.
【9】钱苗根. 现代表面技术[M]. 北京:机械工业出版社, 2004.
【10】杨孚标, 肖加余, 曾竟成, 等. 铝合金磷酸阳极氧化和胶接性能分析[J]. 中国表面工程, 2005, 18(4):37-40.
【11】Lu Y, Wu F, Xue G, et al. Interfacial modification for an aluminum/ epoxy resin laminated composite[J]. Composite Interface, 1994, 2(4):265-269.
【12】杜先智, 丁明桐, 丁秀芬. 新型铝合金阳极氧化膜的机械特性和组织结构[J]. 安徽师大学报(自然科学版), 1997, 20(1):59-61.
相关信息