Thermal Compression Deformation Behavior of 7B50 Aluminum Alloy
摘 要
在变形温度为300~460 ℃、应变速率为0.001~1 s-1的条件下, 采用Gleeble-1500型热模拟试验机对7B50铝合金的热压缩变形行为进行了研究。结果表明: 7B50铝合金在热压缩变形中的流变应力随着温度的升高而减小, 随着应变速率的提高而增大; 该合金的热压缩变形流变应力可用Z参数公式来描述; 在变形温度较高或应变速率较低时合金发生部分再结晶; 该合金在460 ℃、应变速率为0.1 s-1的热变形条件下出现了明显的动态回复与动态再结晶现象。
Abstract
The thermal compression deformation behavior of 7B50 aluminum alloy was investigated at the temperatures from 300 to 460 ℃ and strain rates from 0.001 to 1 s-1 on Gleeble-1500 thermal simulator. The results show that the flow stress decreased with increasing the deforming temperature and increased with increasing the strain rate during thermal compression deformation process.The flow stress of the alloy during thermal compression deformation could be described by the formula of Z parameter. Partial recystallization took place in the alloy deformed at higher deformation temperature or lower strain rate.The alloy showed significant dynamic recovery and recrystallization phenomena at 460 ℃ and strain rate of 0.1 s-1.
中图分类号 TG146.2
所属栏目
基金项目
收稿日期 2010/11/6
修改稿日期 2011/3/10
网络出版日期
作者单位点击查看
备注隆平(1969-), 女, 湖南株洲人, 副教授, 硕士。
引用该论文: LONG Ping,PAN Qing-lin,ZHOU Jian,LIU Xiao-yan,HE Yun-bin. Thermal Compression Deformation Behavior of 7B50 Aluminum Alloy[J]. Materials for mechancial engineering, 2011, 35(11): 32~35
隆平,潘清林,周坚,刘晓艳,何运斌. 7B50铝合金的热压缩变形行为[J]. 机械工程材料, 2011, 35(11): 32~35
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】易幼平,杨积慧,蔺永诚.7050铝合金热压缩变形的流变应力本构方程[J]. 材料工程,2007(4):20-26.
【2】李俊鹏,沈健,闫晓东,等. 温度对7075铝合金热变形显微组织演化的影响[J]. 中国有色金属学报,2008(11):1951-1957.
【3】周建, 张廷杰, 张小明, 等.[J]. 稀有金属材料与工程,2004(6):580-584.
【4】盛永华,王新云,夏巨谌.7475铝合金高温高应变速率压缩变形的流变应力[J]. 锻压装备与制造技术,2005(4):98-100.
【5】POIRIER J P.晶体的高温塑性变形[M]. 关德林, 译. 大连:大连理工大学出版社,1989.
【6】JONAS J J, SELLARS C M, TEGART M W J. Strength and structure under hot working conditions[J]. International Metallurgical Reviews,1969,130(14):1-24.
【7】SHEPPARD T, PARSON N C, ZAIDI M A. Dynamic recrystallization in Al-7Mg alloy[J]. Metal Science,1983,17(10):481-490.
【8】ZENER C, HOLLOMON J H. Effect of strain-rate upon the plastic flow of steel[J]. Journal of Applied Physics,1944,15(1):22-27.
【9】刘晓艳,潘清林,何运斌,等. Al-Cu-Mg-Ag合金热压缩变形的流变应力行为和显微组织[J]. 中国有色金属学报,2009,2(2):201-207.
【2】李俊鹏,沈健,闫晓东,等. 温度对7075铝合金热变形显微组织演化的影响[J]. 中国有色金属学报,2008(11):1951-1957.
【3】周建, 张廷杰, 张小明, 等.[J]. 稀有金属材料与工程,2004(6):580-584.
【4】盛永华,王新云,夏巨谌.7475铝合金高温高应变速率压缩变形的流变应力[J]. 锻压装备与制造技术,2005(4):98-100.
【5】POIRIER J P.晶体的高温塑性变形[M]. 关德林, 译. 大连:大连理工大学出版社,1989.
【6】JONAS J J, SELLARS C M, TEGART M W J. Strength and structure under hot working conditions[J]. International Metallurgical Reviews,1969,130(14):1-24.
【7】SHEPPARD T, PARSON N C, ZAIDI M A. Dynamic recrystallization in Al-7Mg alloy[J]. Metal Science,1983,17(10):481-490.
【8】ZENER C, HOLLOMON J H. Effect of strain-rate upon the plastic flow of steel[J]. Journal of Applied Physics,1944,15(1):22-27.
【9】刘晓艳,潘清林,何运斌,等. Al-Cu-Mg-Ag合金热压缩变形的流变应力行为和显微组织[J]. 中国有色金属学报,2009,2(2):201-207.
相关信息