Reciprocating Extrusion Technology and Grain Refinement of Industrial Pure Magnesium
摘 要
在150, 175, 200, 225, 250 ℃对工业纯镁进行不同道次的往复挤压, 用光学显微镜研究了挤压温度和挤压道次对晶粒细化效果的影响。结果表明: 150 ℃是工业纯镁能够进行往复挤压的最低温度; 随着挤压温度的升高, 工业纯镁的塑性提高, 挤压应力下降, 但晶粒细化效果有所下降; 随着挤压道次增加, 晶粒进一步细化; 最佳挤压温度为200 ℃, 最佳挤压道次为4次。
Abstract
Reciprocating extrusion for different passes was carried out for industrial pure magnesiums at 150, 175, 200, 225, 250 ℃. The effects of extrusion temperature and passes on grain refinement were studied by optical microscopy. The results show that the minimum temperature for reciprocating extrusion of industrial pure magnesium was 150 ℃. With the increase of extrusion temperature, the plasticity of industrial pure magnesium increased and the extrusion stress decreased, but the grain refinement effect became worse. With the increase of the extrusion passes, the grain size was refined further. The best extrusion temperature was 200 ℃, and the optimal extrusion passes was 4.
中图分类号 TG376.3
所属栏目 试验研究
基金项目 以色列工学院博士后基金资助项目; 河南理工大学博士基金资助项目(648313); 材料加工学科预研基金资助项目(506081)
收稿日期 2011/3/15
修改稿日期 2011/11/29
网络出版日期
作者单位点击查看
备注陈思杰(1963-), 男, 河南沁阳人, 教授, 博士。
引用该论文: CHEN Si-jie. Reciprocating Extrusion Technology and Grain Refinement of Industrial Pure Magnesium[J]. Materials for mechancial engineering, 2012, 36(4): 9~11
陈思杰. 工业纯镁的往复挤压工艺及晶粒细化效果[J]. 机械工程材料, 2012, 36(4): 9~11
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】张津, 章宗和. 镁合金及其应用[M].北京: 化学工业出版社, 2004.
【2】FOLEY D C, MAHARBI M A, HARTWIG K T, et al. Grain refinement vs crystallographic texture: Mechanical anisotropy in a magnesium alloy[J].Scripta Materialia, 2011, 64: 193-196.
【3】关绍康, 王迎新.高温镁合金的研究进展及其在汽车工业中的应用[J].机械工程材料, 2003, 27(8): 1-4.
【4】TSAI M H, CHEN M S, LIN L H. Effect of heat treatment on the microstructures and damping properties of biomedical Mg-Zr alloy[J].Journal of Alloys and Compounds, 2011, 509: 813-819.
【5】杨光昱, 介万奇, 郝启堂. 铸造合金的组织和室温力学性能[J].中国有色金属学报, 2006, 16(2): 205-212.
【6】宋佩伟.往复挤压Mg-Al-Si合金的组织、性能及强化机制[D].西安: 西安理工大学, 2007.
【7】郭学锋, 杨文朋, 宋佩维.往复挤压Mg-4Al-2Si合金的高温拉伸性能[J].有色金属学报, 2010, 20(6): 1033-1039.
【8】POLMEAR I J. Magnesium alloys and applications[J].Mater Sci & Tech, 1994, 10(1): 1-16.
【9】MABUCHI M, IWASAKI H, YANASE K.et al.Low temperature superplasticity in an AZ91 magnesium alloy processed by ECAE[J].Scripta Mate, 1997, 36(6): 681-686.
【10】徐春杰, 郭学锋, 张忠明, 等.往复挤压及正挤压AZ91D镁合金丝材的组织及性能[J].稀有金属材料与工程, 2007, 36(3): 500-504.
【11】金文中, 刘顺华.镁合金焊丝的热挤压-拉拔工艺及其变形机理[J].材料科学与工艺, 2005, 13(5): 466-468.
【2】FOLEY D C, MAHARBI M A, HARTWIG K T, et al. Grain refinement vs crystallographic texture: Mechanical anisotropy in a magnesium alloy[J].Scripta Materialia, 2011, 64: 193-196.
【3】关绍康, 王迎新.高温镁合金的研究进展及其在汽车工业中的应用[J].机械工程材料, 2003, 27(8): 1-4.
【4】TSAI M H, CHEN M S, LIN L H. Effect of heat treatment on the microstructures and damping properties of biomedical Mg-Zr alloy[J].Journal of Alloys and Compounds, 2011, 509: 813-819.
【5】杨光昱, 介万奇, 郝启堂. 铸造合金的组织和室温力学性能[J].中国有色金属学报, 2006, 16(2): 205-212.
【6】宋佩伟.往复挤压Mg-Al-Si合金的组织、性能及强化机制[D].西安: 西安理工大学, 2007.
【7】郭学锋, 杨文朋, 宋佩维.往复挤压Mg-4Al-2Si合金的高温拉伸性能[J].有色金属学报, 2010, 20(6): 1033-1039.
【8】POLMEAR I J. Magnesium alloys and applications[J].Mater Sci & Tech, 1994, 10(1): 1-16.
【9】MABUCHI M, IWASAKI H, YANASE K.et al.Low temperature superplasticity in an AZ91 magnesium alloy processed by ECAE[J].Scripta Mate, 1997, 36(6): 681-686.
【10】徐春杰, 郭学锋, 张忠明, 等.往复挤压及正挤压AZ91D镁合金丝材的组织及性能[J].稀有金属材料与工程, 2007, 36(3): 500-504.
【11】金文中, 刘顺华.镁合金焊丝的热挤压-拉拔工艺及其变形机理[J].材料科学与工艺, 2005, 13(5): 466-468.
相关信息