Effect of Tension on Surface Quality of Electronic Aluminum Foil during Rolling
摘 要
在不同张力下对电子铝箔进行轧制, 分析了电子铝箔的轧制力、厚度差、表面形貌、位错密度和表面残余应力, 观察了制备的电极箔的表面形貌。结果表明: 在试验条件下降低张力轧制电子铝箔, 可使轧制力、表面粗糙度和位错密度增大, 但表面残余应力变小, 且均匀厚度差变小, 从而在电子铝箔表面形成细而密的腐蚀孔, 有利于提高电极箔的比电容。
Abstract
The electronic aluminum foil was rolled under different tensions. The rolling force, thickness difference, surface morphology, dislocation density and surface residual stress of electron aluminum foil were analyzed, and the surface morphology of electrode foil was observed. The results show that decreasing the tension to roll the electronic aluminum foil under the experimental condition caused rolling force, surface roughness and dislocation density increasing, surface residual stress reducing uniformity, and the thickness difference increasing, thus forming fine and dense corrosion holes on electronic foil surface to increase specific capacitance of the electrode foil.
中图分类号 TG335.5 TG146.2
所属栏目 材料性能及其应用
基金项目
收稿日期 2011/5/13
修改稿日期 2012/2/10
网络出版日期
作者单位点击查看
备注周亚军(1965-), 男, 湖南望城人, 副研究员, 硕士。
引用该论文: ZHOU Ya-jun,CHENG Feng,HE Xiao-long. Effect of Tension on Surface Quality of Electronic Aluminum Foil during Rolling[J]. Materials for mechancial engineering, 2012, 36(5): 50~53
周亚军,程峰,何小龙. 轧制时张力对电子铝箔表面质量的影响[J]. 机械工程材料, 2012, 36(5): 50~53
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】王祝堂, 田荣璋. 铝合金及其加工手册[M].长沙: 中南大学出版社, 2000.
【2】刘立文, 张树堂, 武志平.张力对冷轧板带变形的影响[J].钢铁, 2000, 35(4): 37-40.
【3】张树堂.轧制超薄带时平整度的研究[J].钢铁, 1982, 16(10): 1-5.
【4】陈长科.张力对大宽厚比铝箔板形影响的有限元分析[J].铝加工, 2005(6): 10-13.
【5】张宏昌, 郗安民, 刘鸿飞.铝箔轧制中张力的厚度调节功效[J].中国机械工程, 2008, 19(14): 1748-1750.
【6】关小军. 轧制润滑技术[M].北京: 化学工业出版社, 2010: 32-34.
【7】陈会丽, 钟毅, 王华昆, 等.残余应力测试方法的研究进展[J].云南冶金, 2005, 34(3): 52-54.
【8】朱伟.7075铝合金厚板淬火残余应力的研究[D].长沙: 中南大学, 2002.
【9】MAO Wei-min, JIANG Heng, YANG Ping. Distribution of microelements and their influence on the corrosion behavior of aluminum foil[J].Journal of Materials Science & Technology, 2005, 21(1): 43-46.
【2】刘立文, 张树堂, 武志平.张力对冷轧板带变形的影响[J].钢铁, 2000, 35(4): 37-40.
【3】张树堂.轧制超薄带时平整度的研究[J].钢铁, 1982, 16(10): 1-5.
【4】陈长科.张力对大宽厚比铝箔板形影响的有限元分析[J].铝加工, 2005(6): 10-13.
【5】张宏昌, 郗安民, 刘鸿飞.铝箔轧制中张力的厚度调节功效[J].中国机械工程, 2008, 19(14): 1748-1750.
【6】关小军. 轧制润滑技术[M].北京: 化学工业出版社, 2010: 32-34.
【7】陈会丽, 钟毅, 王华昆, 等.残余应力测试方法的研究进展[J].云南冶金, 2005, 34(3): 52-54.
【8】朱伟.7075铝合金厚板淬火残余应力的研究[D].长沙: 中南大学, 2002.
【9】MAO Wei-min, JIANG Heng, YANG Ping. Distribution of microelements and their influence on the corrosion behavior of aluminum foil[J].Journal of Materials Science & Technology, 2005, 21(1): 43-46.
相关信息