Effects of Reheat Treatment on Microstructure and Properties of X100 Pipeline Steels
摘 要
将X100管线钢在850, 950, 1 050, 1 150 ℃淬火后再分别在250, 350, 550 ℃下回火, 以及将X100管线钢直接在250, 350, 550 ℃下回火, 分别用以研究再加热工艺对X100管线钢弯管和直管组织与性能的影响; 然后在不同温度下进行冲击试验, 并对淬火和回火前后的冲击断口形貌进行了分析。结果表明: X100管线钢经950 ℃淬火和550 ℃回火后, 显微组织为贝氏体、多边形铁素体和珠光体, 且其硬度适中, 冲击断口的纤维区、放射区、剪切区均呈韧窝形貌, 可与母管实现良好的强韧性匹配; X100管线钢在550 ℃直接回火后, 组织为回火索氏体, 组织均匀, 硬度适中, 可与母管相匹配。
Abstract
The effects of reheat treatment on microstructure and properties of the bend pipe and straight pipe of X100 pipeline steel were studied by quenching them at 850, 950, 1 050, 1 150 ℃ and then tempering at 250, 350, 450, 550 ℃, or only tempering at 250, 350, 450, 550 ℃, respectively to gain the optimized technological parameters. The impact toughness was measured at different temperatures and the fracture morphology of samples before and after reheating treatment was analyzed. The results show that, when the steel was quenched at 950 ℃ and then tempered at 550 ℃, its microstruecture was B+PF+P, the hardness was moderate, the impact fracture exhibited good dimples in the fibrous region, radial region and shear zone, indicating a good match with the main pipe. When the steel was directly tempered at 550 ℃, the microstructure was homogenous, the hardness was moderate, also matched with the main pipe
中图分类号 TG142.1
所属栏目 试验研究
基金项目 国家一等博士后基金资助项目(20060390319)
收稿日期 2012/6/10
修改稿日期 2013/4/26
网络出版日期
作者单位点击查看
备注张小立(1969-), 女, 甘肃武威人, 高级工程师, 博士后。
引用该论文: ZHANG Xiao-li. Effects of Reheat Treatment on Microstructure and Properties of X100 Pipeline Steels[J]. Materials for mechancial engineering, 2013, 37(7): 6~9
张小立. 再加热工艺对X100管线钢组织和性能的影响[J]. 机械工程材料, 2013, 37(7): 6~9
被引情况:
【1】徐亮,章小浒,黄金国,方国爱,江慧丰,李书瑞, "700 MPa级低碳微合金钢的连续冷却相变组织及强韧性",机械工程材料 39, 29-35(2015)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】KNODO J, TAKAGISHI M. Development of induction bend pipe[C]// Proceedings of OMAE′02.Oslo, Norway: ASME, 2002.
【2】马永山.控轧钢UOE管热煨弯管弯制工艺研究[D].天津: 天津大学, 2004.
【3】王英杰.金属材料及热处理[M].北京: 机械工业出版社, 2007.
【4】刘迎来, 池强, 王鹏.加热温度对X80弯管钢组织与性能的影响[J].金属热处理, 2010, 35(10): 25-30.
【5】张小立, 张勇, 李刚.X80级弯管热处理工艺和组织性能相关性研究[J].中原工学院学报, 2011, 22(2): 8-13.
【6】张小立, 冯耀荣, 赵文轸, 等.X80级管线钢的组织和力学性能[J].特殊钢, 2006, 27( 3): 11-13.
【2】马永山.控轧钢UOE管热煨弯管弯制工艺研究[D].天津: 天津大学, 2004.
【3】王英杰.金属材料及热处理[M].北京: 机械工业出版社, 2007.
【4】刘迎来, 池强, 王鹏.加热温度对X80弯管钢组织与性能的影响[J].金属热处理, 2010, 35(10): 25-30.
【5】张小立, 张勇, 李刚.X80级弯管热处理工艺和组织性能相关性研究[J].中原工学院学报, 2011, 22(2): 8-13.
【6】张小立, 冯耀荣, 赵文轸, 等.X80级管线钢的组织和力学性能[J].特殊钢, 2006, 27( 3): 11-13.
相关信息