Research and Comparison on Residual Stresses Measurement by Two Different Methods
摘 要
先用X射线衍射法再用盲孔法测定了同一试样的残余应力, 对测试结果进行了分析比较。结果表明: 对于残余应力分布不随深度改变的情况, 两者结果一致; 但对于其他情况, 两种方法得到的结果不一致。通过测试残余应力沿试样深度的分布和从原理上比较两种测试方法的不同, 得出盲孔法的测试结果受深层残余应力分布影响, 而X射线衍射法的测试结果不受其影响。
Abstract
The residual stress of specimen has determined by two different methods including the X-ray diffraction method and the blind-hole method. Compared with the results of two methods, it was found that, they were same in the condition that residual stress didn’t change with depth; but in other condition, the results of X-ray diffraction method were a little higher than the results of blind-hole method. By measuring the residual stresses in depth and studying on the principles of two methods, the conclusion was reached that the results of blind-hole method were influenced by the residual stress in depth but the results of X-ray diffraction method were not.
中图分类号 TG115.22+2.2
所属栏目
基金项目
收稿日期 2011/4/13
修改稿日期
网络出版日期
作者单位点击查看
备注王超逸(1983-), 男, 工程师, 硕士。
引用该论文: WANG Chao-yi,LV Dan,SU Hong-ying,YU Xiu-e,YANG Cheng-bo,SUN Shao-guang. Research and Comparison on Residual Stresses Measurement by Two Different Methods[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2011, 47(11): 690~693
王超逸,吕丹,苏洪英,于秀蛾,杨成波,孙绍广. 两种残余应力测定方法的研究和比较[J]. 理化检验-物理分册, 2011, 47(11): 690~693
被引情况:
【1】王超逸,吕丹,苏洪英,孙绍广,杨承波, "测定钢板残余应力的改进盲孔法",理化检验-物理分册 51, 781-783(2015)
【2】房元斌,张贵芝,张立平,孔祥意,占小红, "Q890D高强钢中厚板焊接接头残余应力的有限元模拟",机械工程材料 40, 73-76(2016)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】曾纪杰,熊渊博. 金属板材成型中的残余应力与失稳分析[J]. 塑性工程学报, 2005, 12(2) : 82-84.
【2】米谷茂.残余应力的产生和对策[M].朱荆璞, 邵会孟,译.北京: 机械工业出版社, 1983.
【3】日本材料学会X射线测定部分委员会.X射线应力测定法与机械应力测定法的对应关系[J].材料, 1964, 13(135): 909-914.
【4】潘红良, 李培宁, 李炜.焊接残余应力测试方法的研究[J].压力容器,1991, 8(2): 36-39.
【5】张定铨.残余应力测定的基本知识——X射线应力测定的基本原理[J].理化检验-物理分册,2007,43(5):263-265.
【6】CB 3395-1992残余应力测量方法——钻孔应变释放法[S].
【7】张定铨, 何家文.材料中残余应力的X射线衍射分析和作用[M].西安: 西安交通大学出版社, 1999: 12-14.
【8】MAXWELL A. Measurement of residual stress in engineering plastics using the hole-drilling technique[J].Polymer Testing, 2003,23(1): 231-233.
【9】刘金艳. X射线残余应力的测量技术与应用研究[D].北京: 北京工业大学,2009.
【10】张雅琴, 张小平, 郭会光, 等.冷轧带钢残余应力及其对板形影响的研究[J].塑性工程学报, 2009,16(5):75-79.
【2】米谷茂.残余应力的产生和对策[M].朱荆璞, 邵会孟,译.北京: 机械工业出版社, 1983.
【3】日本材料学会X射线测定部分委员会.X射线应力测定法与机械应力测定法的对应关系[J].材料, 1964, 13(135): 909-914.
【4】潘红良, 李培宁, 李炜.焊接残余应力测试方法的研究[J].压力容器,1991, 8(2): 36-39.
【5】张定铨.残余应力测定的基本知识——X射线应力测定的基本原理[J].理化检验-物理分册,2007,43(5):263-265.
【6】CB 3395-1992残余应力测量方法——钻孔应变释放法[S].
【7】张定铨, 何家文.材料中残余应力的X射线衍射分析和作用[M].西安: 西安交通大学出版社, 1999: 12-14.
【8】MAXWELL A. Measurement of residual stress in engineering plastics using the hole-drilling technique[J].Polymer Testing, 2003,23(1): 231-233.
【9】刘金艳. X射线残余应力的测量技术与应用研究[D].北京: 北京工业大学,2009.
【10】张雅琴, 张小平, 郭会光, 等.冷轧带钢残余应力及其对板形影响的研究[J].塑性工程学报, 2009,16(5):75-79.
相关信息