Measurement of Thermo-physical Parameters of 55CrMo Steel
摘 要
分别采用排水法、闪光法和比较法测定了55CrMo钢的室温密度、热扩散率和比热容, 并计算得出了该钢的导热系数。结果表明: 随着温度的升高, 55CrMo钢的比热容总体上呈上升趋势, 而热扩散率和导热系数则以相反趋势变化, 且该三个热物性参数均在相变区内有所波动; 测定结果为开展55CrMo钢感应加热淬火过程的有限元模拟提供了重要的试验数据。
Abstract
The room temperature density, thermal diffusivity and specific heat of 55CrMo steel had been measured by displacement way, flash method and comparison method, respectively. And the heat conductivity of the steel was also be calculated. The results show that the specific heat of 55CrMo steel increased generally with the increase of temperature, while the thermal diffusivity and heat conductivity changed in a contradictory tendency. All these these parameters fluctuated during the temperature zone of phase transformation. The experimental results provided some important data for the numerical simulation of induction quenching process of 55CrMo steel.
中图分类号 TG115.25
所属栏目 试验技术与方法
基金项目 国家工信部重大专项课题资助项目(2011ZX04014-031)
收稿日期 2011/8/14
修改稿日期
网络出版日期
作者单位点击查看
备注王倩(1990-),女,硕士研究生。
引用该论文: WANG Qian,LI Hui-ping,LI Bao-min,DING Xia,LI Mu-sen. Measurement of Thermo-physical Parameters of 55CrMo Steel[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2012, 48(2): 109~111
王倩,李辉平,李保民,丁霞,李木森. 55CrMo钢热物性参数的测定[J]. 理化检验-物理分册, 2012, 48(2): 109~111
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】赖宏,刘天模. 45钢零件淬火过程温度场的ansys模拟[J]. 重庆大学学报,2003,26(3):82-87.
【2】屠海令,干勇. 金属材料理化测试全书[M]. 北京:化学工业出版社,2007:188-189.
【3】李婉秋,路宗奎,曲春浴. LTC-1000型激光热导仪及对炭制品的测试[J]. 炭素,2007(1):37-41.
【4】王平. 比较法测比热的原理分析[J]. 广西物理,2000,24(4):35-36.
【5】应诗浩,吉忠昌. 激光脉冲法测量比热[J]. 核动力工程,1981,2(5):67-70.
【6】赵建国,李克智,李贺军. 炭/炭复合材料导热性能的研究[J]. 航空学报,2005,26(4):1-4.
【7】刘靖,温志强,余万华. B510L钢热物性参数的研究[J]. 河南冶金,2007,15(5):9-18.
【2】屠海令,干勇. 金属材料理化测试全书[M]. 北京:化学工业出版社,2007:188-189.
【3】李婉秋,路宗奎,曲春浴. LTC-1000型激光热导仪及对炭制品的测试[J]. 炭素,2007(1):37-41.
【4】王平. 比较法测比热的原理分析[J]. 广西物理,2000,24(4):35-36.
【5】应诗浩,吉忠昌. 激光脉冲法测量比热[J]. 核动力工程,1981,2(5):67-70.
【6】赵建国,李克智,李贺军. 炭/炭复合材料导热性能的研究[J]. 航空学报,2005,26(4):1-4.
【7】刘靖,温志强,余万华. B510L钢热物性参数的研究[J]. 河南冶金,2007,15(5):9-18.
相关信息