Reasons Analysis on Fracture of φ102 mm×9.19 mm DZ55 Geological Drill Pipe Body
摘 要
通过宏观分析、金相检验、化学成分分析、力学性能测试和扫描电镜微观分析对一DZ55钢级φ102 mm×9.19 mm地质钻杆的断裂原因进行了分析。结果表明: 因该地质钻杆管体外壁存在较多的螺旋状划痕和刮蹭痕迹造成应力集中, 加之钻杆材料韧性较低, 从而导致钻杆管体在钻进过程中于损伤处萌生裂纹, 裂纹不断扩展最终发生脆性断裂。
Abstract
Fracture reasons of a geological drill pipe with grade of DZ55 and size of φ102 mm×9.19 mm were analyzed through macro observation, metallographic examination, chemical compositions analysis, mechanical property test and SEM analysis. The results show that there were a lot of spiral scribes and scratches on outer surface of the drill pipe body, which caused stress concentration. At the same time, and material toughness of the drill pipe body was rather low. So cracks generated at the damage positions and finally brittle fracture happened during drilling process of the drill pipe.
中图分类号 T921.2
所属栏目 质量控制与失效分析
基金项目
收稿日期 2011/8/5
修改稿日期
网络出版日期
作者单位点击查看
备注张金源(1986-), 男, 硕士研究生。
引用该论文: ZHANG Jin-yuan,TONG Lin,GAO Wei,LIU Qing-lin. Reasons Analysis on Fracture of φ102 mm×9.19 mm DZ55 Geological Drill Pipe Body[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2012, 48(6): 410~413
张金源,佟琳,高伟,刘箐霖. DZ55钢级φ102 mm×9.19 mm地质钻杆管体断裂原因分析[J]. 理化检验-物理分册, 2012, 48(6): 410~413
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】《钻井手册(甲方)》编写组.钻井手册[M]. 北京:石油工业出版社,1990:921.
【2】BARYSHNIKOV A, CALDERONI A, LNGELO A,et al.A new approach to the analysis of drill string fatigue behavior[J]. SPE Drilling & Completion,1997,9(6):77-84.
【3】GB/T 6394-2002金属平均晶粒度测定方法[S].
【4】GB/T 10561-2005钢中非金属夹杂物含量的测定——评级图显微检验法[S].
【5】高洪志,吕拴录,李鹤林,等.随钻震击器断裂事故分析及预防[J]. 石油钻采工艺,1991,13(6):29-35.
【6】吕拴录,王新虎.WS1井φ88.9 mm四方钻杆断裂原因分析[J]. 石油钻采工艺,2004,26(5):47-49.
【7】王新虎,薛继军,谢居良,等.钻杆接头抗扭强度及材料韧性指标研究[J]. 石油矿场机械,2006,35(增刊):1-4.
【2】BARYSHNIKOV A, CALDERONI A, LNGELO A,et al.A new approach to the analysis of drill string fatigue behavior[J]. SPE Drilling & Completion,1997,9(6):77-84.
【3】GB/T 6394-2002金属平均晶粒度测定方法[S].
【4】GB/T 10561-2005钢中非金属夹杂物含量的测定——评级图显微检验法[S].
【5】高洪志,吕拴录,李鹤林,等.随钻震击器断裂事故分析及预防[J]. 石油钻采工艺,1991,13(6):29-35.
【6】吕拴录,王新虎.WS1井φ88.9 mm四方钻杆断裂原因分析[J]. 石油钻采工艺,2004,26(5):47-49.
【7】王新虎,薛继军,谢居良,等.钻杆接头抗扭强度及材料韧性指标研究[J]. 石油矿场机械,2006,35(增刊):1-4.
相关信息