搜索热:失效分析 陶瓷
扫一扫 加微信
首页 > 期刊论文 > 论文摘要
高径比对非金属发泡承压件承载能力的影响
          
Influence of Ratio of Height to Diameter on External Endurance Ability of Nonmetallic Frothy Pressure Part

摘    要
某型号非金属发泡承压件在使用中内压极限强度不变, 而外压极限强度偏低。为此通过调整承压件的结构, 研究高径比对非金属发泡承压件的内压极限强度和外压极限强度的影响。结果表明: 当保证内压极限强度不变的情况下, 高径比的增加不利于非金属发泡承压件外压承载能力的提高。
标    签 非金属发泡承压件   结构优化设计   内压极限强度   外压极限强度   高径比   nonmetallic frothy pressure part   construction improved design   ability of internal endurance   ability of external endurance   ratio of height to diameter  
 
Abstract
In use, the ability of internal endurance of a type nonmetallic frothy pressure part was not changed and the ability of external endurance of that was relatively low. By changing the structure of the part, the influence of ratio of height to diameter on the abilities of internal endurance and external endurance was researched. The results indicated that when the ability of internal endurance of the nonmetallic frothy pressure part was not changed and to enhance the ratio of height to diameter cannot enhance the ability of external endurance.

中图分类号 TQ323.5

 
  中国光学期刊网论文下载说明


所属栏目 试验与研究

基金项目

收稿日期 2011/12/1

修改稿日期

网络出版日期

作者单位点击查看

备注刘宇盖(1978-), 男, 工程师, 硕士研究生。

引用该论文: LIU Yu-gai,CAI Zhen-jie. Influence of Ratio of Height to Diameter on External Endurance Ability of Nonmetallic Frothy Pressure Part[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2012, 48(7): 439~440
刘宇盖,蔡振杰. 高径比对非金属发泡承压件承载能力的影响[J]. 理化检验-物理分册, 2012, 48(7): 439~440


论文评价
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
分享论文
分享到新浪微博 分享到腾讯微博 分享到人人网 分享到 Google Reader 分享到百度搜藏分享到Twitter

参考文献
【1】张中利, 于存贵, 马大为, 等.冲击作用下易碎式密封盖数值仿真及实验分析[J].爆炸与冲击, 2008, 28(1):62-66.
 
【2】姚树燕, 张娜, 魏风春, 等.层合易碎材料的设计与试验[J].河南科技大学学报: 自然科学版, 2009, 30(2): 1-3.
 
【3】孙甫.MY-9易碎材料在武器系统上的应用[J].宇航材料工艺, 2002(2): 25-28.
 
【4】苗佩云, 袁曾凤.同心发射筒燃气开盖技术[J].北京理工大学学报, 2004, 24(4): 283-285.
 
【5】尤风翔, 郝庆东.复合材料层合板随机参数结构的响应分析[J].河南科技大学学报: 自然科学版, 2003, 25(4): 14-19.
 
相关信息
   标题 相关频次
 基于有限元分析的前易碎盖外压承载能力的改进设计
 2
 导弹发射箱用平板型复合材料多瓣薄膜盖的研制
 1
 环氧树脂增韧改性研究进展
 1
 添加聚四氟乙烯微粉后聚醚醚酮复合材料的摩擦学性能
 1
 压电陶瓷粉含量及表面附着微粒对0-3型压电复合材料性能的影响
 1