Problems Analysis and Solution of Compression Test with Hydraulic Wedge for Gleeble-3500 Thermal Analogue
摘 要
Gleeble-3500型热/力模拟试验机在更换液压楔进行压缩试验时易出现应变速率、应变量达不到程序设定的要求以及试样变形不均匀、鼓形等问题, 对此进行了分析和处理。结果表明: 通过采用调整试样夹持力、充入氩气保护气体、修改变形程序、保证砧子和试样之间的良好润滑等改进措施可以解决以上问题。
Abstract
There have been some problems of Gleeble-3500 thermal analogue when replacing the hydraulic wedge for compression test including that the strain rate and strain capacity could not meet the requirement of set-up procedure, and the specimen appeared inhomogeneous deformation and drum sharp. The above problems were analyzed and handled. The results showed that the matters can be improved by adjust the force between the jaws and the specimen, fill the argon protect air in the work cavity, modify the deformation procedure and keep suitable lubricant at the interface between the anvils and the specimen.
中图分类号 TH871
所属栏目 试验设备及应用
基金项目
收稿日期 2011/11/19
修改稿日期
网络出版日期
作者单位点击查看
备注孙胜英(1981-), 女, 工程师。
引用该论文: SUN Sheng-ying. Problems Analysis and Solution of Compression Test with Hydraulic Wedge for Gleeble-3500 Thermal Analogue[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2012, 48(7): 452~453
孙胜英. Gleeble-3500热/力模拟压缩试验若干问题的分析与处理[J]. 理化检验-物理分册, 2012, 48(7): 452~453
被引情况:
【1】朱俊峰,隋凤利,左岳,马宏伟, "圆柱体单轴压缩锤头进给与应变测试方法",理化检验-物理分册 51, 323-327(2015)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】杨常春.Gleeble-3500热/力学模拟试验机整体设备特性研究[J].物理测试, 2007,25(6):20-23.
【2】廉晓洁, 贾元伟, 梁敏鉴.Gleeble-3800热模拟试验机故障的检测及处理[J].分析测试技术与仪器, 2006, 12(4): 246-248.
【3】刘志军, 薛秀娟.Gleeble-2000热模拟试验机故障的排除与分析[J].安徽冶金, 2004(4):48-50.
【4】钟鄂康.Gleeble-2000型热模拟试验机液压楔故障的诊断和处理[J].物理测试, 2005, 23(6): 54-57.
【2】廉晓洁, 贾元伟, 梁敏鉴.Gleeble-3800热模拟试验机故障的检测及处理[J].分析测试技术与仪器, 2006, 12(4): 246-248.
【3】刘志军, 薛秀娟.Gleeble-2000热模拟试验机故障的排除与分析[J].安徽冶金, 2004(4):48-50.
【4】钟鄂康.Gleeble-2000型热模拟试验机液压楔故障的诊断和处理[J].物理测试, 2005, 23(6): 54-57.
相关信息