Low Cycle Fatigue Behavior of ZTC4 (Ti-6Al-4V) Titanium Alloy at Room Temperature
摘 要
研究了ZTC4钛合金应变控制的室温低周疲劳行为, 对循环应力-应变和应变疲劳寿命数据进行了分析, 通过双对数线性回归处理, 得出了Manson-Coffin处理模型的疲劳参数。结果表明:ZTC4钛合金总应变幅在0.6%~0.8%时, 材料存在轻度循环软化的现象; 总应变幅为0.4%~0.5%时, 循环初期表现出循环硬化的现象, 而后循环软化。合金的疲劳裂纹萌生于试样表面, 裂纹扩展区存在明显的疲劳条带, 合金疲劳断口呈现韧性断裂特征。
Abstract
Low cycle fatigue (LCF) behavior of ZTC4 titanium alloy has been investigated under fully reversed total strain-controlled mode. The cyclic stress-strain and strain-life data were analyzed to determine the individual strain fatigue parameters of Manson-Coffin model by double logarithm linear regression processing. The results showed that the ZTC4 titanium alloy exhibited an initial slight cyclic hardening, followed by cyclic softening at the total strain amplitude of 0.4%-0.5%, then cyclic softening at a total strain amplitude of 0.6%-0.8%. The fatigue cracks initiated at the surface of the samples. The fatigue crack propagation regions were composed of fatigue striations. The fatigue fracture surface of specimens revealed the fracture characteristics of dimple.
中图分类号 TG146.23
所属栏目 试验与研究
基金项目
收稿日期 2012/2/15
修改稿日期
网络出版日期
作者单位点击查看
备注张仕朝(1982-),男,工程师,硕士。
引用该论文: ZHANG Shi-chao,ZHAO Jia-qi,ZHANG Jian-guo. Low Cycle Fatigue Behavior of ZTC4 (Ti-6Al-4V) Titanium Alloy at Room Temperature[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2013, 49(3): 144~147
张仕朝,赵嘉祺,张建国. ZTC4(Ti-6Al-4V)铸造钛合金的室温低周疲劳行为[J]. 理化检验-物理分册, 2013, 49(3): 144~147
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】南海,谢成目,黄东,等. ZTC4(Ti-6Al-4V)铸造钛合金的退火热处理工艺[J]. 中国铸造装备与技术, 2004(5):1-3.
【2】《中国航空材料手册》编辑委员会. 中国航空材料手册[M]. 2版. 北京: 中国标准出版社, 2001.
【3】刘茜珂,刘昌奎,彭楚峰,等. ZTC4钛合金精铸件电子束焊接接头组织与疲劳行为研究[J]. 失效分析与预防, 2008, 3(3):32-36.
【4】要玉宏,刘江南,马丽,等. 铸造TC4钛合金细节疲劳强度DFRcutoff的研究[J]. 稀有金属材料与工程,2009,38(9): 556-558.
【5】上官晓峰,要玉宏,马丽,等. 应力比对铸造TC4钛合金疲劳裂纹扩展特性的影响[J]. 西安工业大学学报,2009,29(6):1530-1531.
【6】GB/T 15248-2008金属材料轴向等幅低循环疲劳试验方法[S].
【7】王拴柱. 金属疲劳[M]. 福州: 福建科学技术出版社,1985.
【8】谢济洲. 低循环疲劳手册[M]. 北京: 北京航空材料研究院, 1991.
【9】SURESH S. 材料的疲劳[M]. 王中光,译. 北京: 国防工业出版社, 1999:182.
【10】Standard E606Standard Practice for Strain-controlled Fatigue Testing[S]. 2004.
【11】张国栋,苏彬,王泓,等. 弹性模量对低周疲劳性能参数的影响[J]. 航空动力学报,2005,20(5):768-771.
【2】《中国航空材料手册》编辑委员会. 中国航空材料手册[M]. 2版. 北京: 中国标准出版社, 2001.
【3】刘茜珂,刘昌奎,彭楚峰,等. ZTC4钛合金精铸件电子束焊接接头组织与疲劳行为研究[J]. 失效分析与预防, 2008, 3(3):32-36.
【4】要玉宏,刘江南,马丽,等. 铸造TC4钛合金细节疲劳强度DFRcutoff的研究[J]. 稀有金属材料与工程,2009,38(9): 556-558.
【5】上官晓峰,要玉宏,马丽,等. 应力比对铸造TC4钛合金疲劳裂纹扩展特性的影响[J]. 西安工业大学学报,2009,29(6):1530-1531.
【6】GB/T 15248-2008金属材料轴向等幅低循环疲劳试验方法[S].
【7】王拴柱. 金属疲劳[M]. 福州: 福建科学技术出版社,1985.
【8】谢济洲. 低循环疲劳手册[M]. 北京: 北京航空材料研究院, 1991.
【9】SURESH S. 材料的疲劳[M]. 王中光,译. 北京: 国防工业出版社, 1999:182.
【10】Standard E606Standard Practice for Strain-controlled Fatigue Testing[S]. 2004.
【11】张国栋,苏彬,王泓,等. 弹性模量对低周疲劳性能参数的影响[J]. 航空动力学报,2005,20(5):768-771.
相关信息