Influences of Tensile Rate Control Modes and Tensile Rate on Strength Test Results of Cold Rolled Sheet
摘 要
按照GB/T 228.1-2010中推荐的不同拉伸速率控制模式及拉伸速率对冷轧镀锌钢板进行了拉伸对比试验,分析了应变速率、横梁位移速率及应力速率对冷轧薄板规定非比例延伸强度Rp0.2、下屈服强度ReL以及抗拉强度Rm测试结果的影响。结果表明: 采用应变速率进行控制得到的拉伸试验数据相对其他两种速率控制模式更为稳定, 可以最大限度地降低拉伸测试结果的不确定度; 采用0.000 25 s-1的应变速率控制模式所得试验结果的稳定性与采用40~50 MPa·s-1的应力速率控制模式所得结果较为接近; 在不同拉伸速率控制模式下, 提高应变、横梁位移和应力速率均会使屈服强度Rp0.2和ReL增加, 而抗拉强度Rm基本上处于稳定状态。
Abstract
Tensile comparison test was done to cold rolled galvanized steel sheet on different tensile rate control modes and tensile rate according to GB/T 228.1-2010, and the influences of strain rate, crosshead separation rate and stress rate on test results of proof strength of non-proportional Rp0.2, lower yield strength ReL and tensile strength Rm of cold rolled sheet were studied. The results show that the tensile test results on strain rate control mode were more stable than those on the other two rate control modes, and it could reduce the tensile test results uncertainty to minimum. The test results stability with strain rate of 0.000 25 s-1 was close to that with stress rate of 40-50 MPa · s-1. Under different tensile rate control mode, raising strain rate, crosshead separation rate or stress rate, the tested Rp0.2 and ReL would increase, but Rm basically was in steady state.
中图分类号 TG115.5
所属栏目 试验技术与方法
基金项目
收稿日期 2012/8/18
修改稿日期
网络出版日期
作者单位点击查看
备注张有为(1983-),男,工程师,学士。
引用该论文: ZHANG You-wei,QIAO Jian-jun,REN Xue-ping. Influences of Tensile Rate Control Modes and Tensile Rate on Strength Test Results of Cold Rolled Sheet[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2013, 49(4): 233~235
张有为,乔建军,任学平. 拉伸速率控制模式及拉伸速率对冷轧薄板强度测试结果的影响[J]. 理化检验-物理分册, 2013, 49(4): 233~235
被引情况:
【1】孙博,郭子静,姚渴, "速率控制模式对GH4169高温合金拉伸性能的影响",理化检验-物理分册 50, 399-403(2014)
【2】张 赛,孟庆振,谢书港,方 锐,孟宪春,孟宪明, "B250P1低合金钢的动态力学行为及其本构模型",理化检验-物理分册 52, 370-374(2016)
【3】叶姜,樊雷,黄福德, "冷轧低碳钢带人工时效与自然时效行为分析",理化检验-物理分册 51, 462-465(2015)
【4】王丽英, "304不锈钢室温抗拉强度测试的影响因素",理化检验-物理分册 52, 88-91(2016)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】梁新邦,李久林. GB/T 228-2002《金属材料 室温拉伸试验方法》实施指南[M]. 北京: 中国标准出版社,2001.
【2】张卓. 室温拉伸试验过程中拉伸速度的控制[J]. 物理测试,2006,24(4): 61-62.
【3】GB/T 228.1-2010金属材料 拉伸试验 第1部分: 室温试验方法[S].
【4】曾力. 拉伸试验速率对低碳钢力学性能的影响[J]. 理化检验-物理分册,2007,43(1): 6-8.
【5】陈华锋,王滨,黄旭东,等. 拉伸试验的速率探讨[J]. 理化检验-物理分册,2009,45(5): 285-287.
【2】张卓. 室温拉伸试验过程中拉伸速度的控制[J]. 物理测试,2006,24(4): 61-62.
【3】GB/T 228.1-2010金属材料 拉伸试验 第1部分: 室温试验方法[S].
【4】曾力. 拉伸试验速率对低碳钢力学性能的影响[J]. 理化检验-物理分册,2007,43(1): 6-8.
【5】陈华锋,王滨,黄旭东,等. 拉伸试验的速率探讨[J]. 理化检验-物理分册,2009,45(5): 285-287.
相关信息