Influence of Testing Machine Flexibility on Tensile Test Results
摘 要
通过对12组不同工艺生产的性能相对稳定的汽车用钢板在两种不同柔度的试验机上进行拉伸试验,采用传统横梁位移控制模式控制拉伸速率,测试其强度指标和延性指标。结果表明: 在柔度较大的传统楔形夹具试验机上测得的上屈服强度ReH和规定非比例延伸强度Rp0.2比柔度较小的液压平推夹具试验机测得的结果要小,而试验机柔度对下屈服强度ReL、抗拉强度Rm和断后伸长率A测定结果则没有明显的影响; 该结果印证了新国标GB/T 228.1-2010中提出方法A(应变速率控制方法)的重要性和必要性; 同时根据试验机柔度对试验结果影响的差异,提出了方法A在实际执行过程中的建议。
Abstract
Tensile properties of 12 groups of automotive steel plates with relatively stable mechanical properties and produced by different processes were tested on two tensile testing machines with different flexibility in crosshead separation rate controlling mode. The results show that the values of ReH and Rp0.2 which were tested on machine with wedge fixtures and higher flexibility were less than those tested on machine with hydraulic pressure horizon-push fixture and lower flexibility, while the testing machine flexibility had little influence on the values of ReL, Rm and elongation A. The results not only proved the importance and necessity of method A in the new national standard GB/T 228.1-2010, but also gave the proposal about the implementation of method A according to different test conditions.
中图分类号 TG115.5
所属栏目 专题报道
基金项目
收稿日期 2013/1/5
修改稿日期
网络出版日期
作者单位点击查看
备注余立(1984-),男,工程师,硕士。
引用该论文: YU Li,LI Rong-feng,TU Ying-hong. Influence of Testing Machine Flexibility on Tensile Test Results[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2013, 49(8): 501~504
余立,李荣锋,凃应宏. 试验机柔度对拉伸试验结果的影响[J]. 理化检验-物理分册, 2013, 49(8): 501~504
被引情况:
【1】苏英群,潘媛媛,韩永明,谢冠男,吴永超, "三种控制方式在GB/T 228.1-2010中的正确应用",理化检验-物理分册 50, 83-88(2014)
【2】潘淑杰,祝铁柱,于兆斌,杨雷岗,王贵勇,类成华,高永, "金属材料室温拉伸试验速率控制方法和夹持系统的选择",理化检验-物理分册 50, 94-96(2014)
【3】王俊峰,肖若冰, "关于万能试验机执行GB/T 228.1-2010的探讨",理化检验-物理分册 50, 101-105(2014)
【4】于洪民,郑文龙,陶立英, "关于GB/T 228.1-2010的理解、验证及探讨",理化检验-物理分册 50, 89-93(2014)
【5】黄星,谢宏, "从拉伸试验机控制角度理解GB/T 228.1-2010的技术变动",理化检验-物理分册 50, 97-100(2014)
【6】张小康, "GB/T 228.1-2010中试验方法与试验机闭环控制的关系",理化检验-物理分册 50, 246-248(2014)
【7】李荣锋,凃应宏, "关于GB/T228.1-2010的几点修订建议",理化检验-物理分册 50, 863-865(2014)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】GB/T 228.1-2010金属材料 拉伸试验 第1部分: 室温拉伸试验方法[S].
【2】ISO 6892:2009Metallic materials-Tensile testing at ambient temperature[S].
【3】GB/T 228-2002金属材料室温拉伸试验方法[S].
【4】凃应宏. ISO/FDIS 6892-1:2008中方法A推出的背景和意义[J]. 冶金分析,2010(增刊: 物理分册):1255-1259.
【5】AEGERTER J,BLOCHING H,SONNE H M. Influence of the testing speed on the yield/proof strength[J]. Materials Testing,2001,10:393-403.
【2】ISO 6892:2009Metallic materials-Tensile testing at ambient temperature[S].
【3】GB/T 228-2002金属材料室温拉伸试验方法[S].
【4】凃应宏. ISO/FDIS 6892-1:2008中方法A推出的背景和意义[J]. 冶金分析,2010(增刊: 物理分册):1255-1259.
【5】AEGERTER J,BLOCHING H,SONNE H M. Influence of the testing speed on the yield/proof strength[J]. Materials Testing,2001,10:393-403.
相关信息