The Exploration about EDA Simulation Principle in Time Measurement of Ultrasonic Bolt Axial Stress Measurement Technique
摘 要
基于超声波激励螺栓产生受迫振动的振动方程与RLC电路微分方程的一致性,建立了电路参数中电感、电容、电阻与超声波传播过程中螺栓的质量、力顺、力阻的一一对应关系,将影响螺栓中声时测量的力学量等效为电路参量。在此基础上,利用EDA (电子设计自动化)仿真软件,分析了电路参数的变化对声时的影响,拟合了电阻、电容与声时差的关系式。EDA仿真得出的电阻、电容对声时的影响规律与实例测量结果自洽,说明了通过EDA仿真的方法研究声时测量的可行性。
Abstract
Based on the identity of oscillatory differential equation between vibration excited by ultrasonic wave propagating in bolts and RLC electric circuit, the one to one correspondence between the mechanical parameter(such as mass, mechanical compliance mechanical resistance) and the circuit parameter(such as inductance, capacitance, resistance) was established. The mechanical parameters affecting the measurement of sound time(time of ultrasonic wave propagating in the bolt) were equivalent to circuit parameter. And then, using EDA(Electronic Design Automation) simulation software, the effect on sound time caused by the change of circuit parameters was analyzed, a relationship of sound time and circuit capacitance and resistance were fitted. The simulation result shows that the relationship and practical measurement are self-consistent, and it proved that the problem of sound time could be simulated by EDA.
中图分类号 TG115.28
所属栏目 科研成果与学术交流
基金项目 南通大学自然科学基金资助项目(07Z037);南通大学研究生科技创新资助项目(YKC08009)
收稿日期 2010/8/11
修改稿日期
网络出版日期
作者单位点击查看
备注莫亚梅(1968-),女,副教授,硕士,研究方向为机械设计及理论。
引用该论文: MO Ya -Mei,YUAN Guo -Qiu,LI Guang. The Exploration about EDA Simulation Principle in Time Measurement of Ultrasonic Bolt Axial Stress Measurement Technique[J]. Nondestructive Testing, 2011, 33(5): 19~21
莫亚梅,袁国秋,李光. 螺栓轴向压力超声检测中声时测量的EDA仿真原理[J]. 无损检测, 2011, 33(5): 19~21
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】杜刚民,李东风,曹树林,等.螺栓轴向应力超声测量技术[J].无损检测,2006,28(1):20-22.
【2】Jhang K Y, Quan H H, Ha J, et al. Estimation of clamping force in high-tension bolts through ultrasonic velocity measurement[J]. Ultrasonics,2006,44(s1):1339-1342.
【3】张俊,顾临怡,钱筱林,等.钢结构工程中高强度螺栓轴向应力的超声测量技术[J].机械工程学报,2006,42(6):216-220.
【4】江泽涛,朱士明.纵横波测已紧固螺栓轴向应力[J].应用声学,2000,19(1):17.
【5】张海澜.理论声学[M].北京:高等教育出版社,2007.
【6】钱大庆.李萨如图形法和相位比较法测量声速精度的研究[J].科技资讯,2007(32):237-238.
【7】刘贵民.无损检测技术[M].北京:国防工业出版社,2006:62-63.
【8】秦曾煌.电工学[M].北京:高等教育出版社,2004:101-148.
【2】Jhang K Y, Quan H H, Ha J, et al. Estimation of clamping force in high-tension bolts through ultrasonic velocity measurement[J]. Ultrasonics,2006,44(s1):1339-1342.
【3】张俊,顾临怡,钱筱林,等.钢结构工程中高强度螺栓轴向应力的超声测量技术[J].机械工程学报,2006,42(6):216-220.
【4】江泽涛,朱士明.纵横波测已紧固螺栓轴向应力[J].应用声学,2000,19(1):17.
【5】张海澜.理论声学[M].北京:高等教育出版社,2007.
【6】钱大庆.李萨如图形法和相位比较法测量声速精度的研究[J].科技资讯,2007(32):237-238.
【7】刘贵民.无损检测技术[M].北京:国防工业出版社,2006:62-63.
【8】秦曾煌.电工学[M].北京:高等教育出版社,2004:101-148.
相关信息