Discussion on Practical Inspecting Condition for Welded Joints in Steel Structural Components By Using Ultrasonic Phased Array Techniques
摘 要
为提高对大型钢结构件的大板梁所有焊接接头的超声检测速度,采用相控阵UT,以电子扫描技术取代常规UT中探头的机械移动。根据有关工业标准要求,通过校验试块的验证试验,探讨分析相控阵超声检测的实际有效探伤条件。试验表明,只要五参数(声束聚焦位置、同时激励的阵元数、有效探伤范围、脉冲重复频率及探伤数据压缩比)正确设定,可明显提高钢结构件焊接接头相控阵UT的检测效率。
Abstract
For increasing the UT speed of inspecting all of the welded joints in large-scale steel structure, the phased array UT was applied with electronic scanning in lieu of mechanical movement of the conventional probe. Based on the relevant industrial standard, this article made a discussion about the effective inspecting condition in this field, through the test demonstration on the calibration blocks. The test verified that so long as the five parameters were set up correctly, such as the beam-focusing location, the number of elements energized simultaneously, the effective test range, the pulse repeating frequency and the test data compression ratio,the efficiency of phased array inspection for welds in steel structure could be raised obviously.
中图分类号 TG115.28
所属栏目 试验研究
基金项目
收稿日期 2010/5/31
修改稿日期
网络出版日期
作者单位点击查看
备注李衍(1940-),男,高级工程师。2004年受聘于江苏太湖锅炉股份有限公司任高级技术顾问。
引用该论文: LI Yan. Discussion on Practical Inspecting Condition for Welded Joints in Steel Structural Components By Using Ultrasonic Phased Array Techniques[J]. Nondestructive Testing, 2011, 33(8): 13~20
李衍. 钢结构件焊接接头超声相控阵实际探伤条件的研讨[J]. 无损检测, 2011, 33(8): 13~20
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】GB 11345—1989钢焊缝手工超声波探伤方法和探伤结果分级[S].
【2】GB/T18694—2002无损检测超声检验探头及其声场的表征[S].
【3】GB/T 18852—2002无损检测超声检验测量接触探头声束特性的参考试块和方法[S].
【4】JIS Z 3070—1998鋼溶接部の超音波自動探傷方法[S].
【5】平澤泰治.フェ一 ズドアレイ法を用いた炉内機器溶接部の超音波探傷技術の開発[J].溶接技術,2001,49(10):68-72.
【6】Masakazu KAMIBAYASHI, Hiroshi KATSUURA, Keiji HATTORI. Study of automatic ultrasonic testing using phased array UT techniques for welded joints[J]. JSNDI,2009,58(12):556-562.
【7】李衍.超声相控阵检测技术系列讲座[J].无损探伤,2007,31(4,6);2008,32(1,4,6).
【2】GB/T18694—2002无损检测超声检验探头及其声场的表征[S].
【3】GB/T 18852—2002无损检测超声检验测量接触探头声束特性的参考试块和方法[S].
【4】JIS Z 3070—1998鋼溶接部の超音波自動探傷方法[S].
【5】平澤泰治.フェ一 ズドアレイ法を用いた炉内機器溶接部の超音波探傷技術の開発[J].溶接技術,2001,49(10):68-72.
【6】Masakazu KAMIBAYASHI, Hiroshi KATSUURA, Keiji HATTORI. Study of automatic ultrasonic testing using phased array UT techniques for welded joints[J]. JSNDI,2009,58(12):556-562.
【7】李衍.超声相控阵检测技术系列讲座[J].无损探伤,2007,31(4,6);2008,32(1,4,6).
相关信息