箔材、薄板和中板的超声爬波检测
Ultrasonic Creeping Wave Testing for Foil,Sheet and Plate
摘 要
描述了箔材(厚度≤0.5 mm)、薄板(厚度0.5~6 mm)和中板(厚度≥6 mm)的超声爬波检测技术.同时,采用手动接触法超声爬波检测技术,给出了厚度为0.2 mm钛合金箔材和厚度为16 mm钼合金中板的超声爬波实际检测结果和相关数据,还给出了厚度为0.5 mm纯钛薄板和厚度为20 mm钛合金中板的一些超声爬波检测试验结果和相关数据.结果表明,箔材、薄板和中板的超声爬波检测技术是可行和有效的.
单晶片爬波探头
盲区
箔材
薄板
中板
Ultrasonic testing
Single crystal creeping wave probe
Dead zone
Foil
Sheet
Plate
Abstract
Ultrasonic creeping wave testing technique of foils (thickness≤0.5 mm),sheets(thickness 0.5~6 mm) and plates (thickness≥6 mm) is described in this paper.At the same time,ultrasonic creeping wave testing practical examination results and relevant data for TC4 Ti alloy foils with thickness 0.2 mm and Mo alloy plates with thickness 16mm have also given by manual contact method ultrasonic creeping wave testing technique.Besides,ultrasonic creeping wave experimental testing results and relevant data etc for TA2 Ti sheets with thickness 0.5 mm and TC4 Ti alloy plates with thickness 20 mm have also been given by manual contact method ultrasonic creeping wave testing technique.Practical examination results and relevant data etc demonstrated that the ultrasonic creeping wave testing technique for foil,sheet and plate was correct and efficient.
中图分类号 TG115.28
所属栏目 试验研究
基金项目
收稿日期 2014/12/15
修改稿日期
网络出版日期
作者单位点击查看
备注郑开胜(1941-),男,教授级高工,主要从事超声波探头的研制和检测方法的研究,以及检测标准的制订工作.
引用该论文: ZHENG Kai-sheng,GONG Ya-lin,SUN Hai-xia,CHEN Jun-wei. Ultrasonic Creeping Wave Testing for Foil,Sheet and Plate[J]. Nondestructive Testing, 2015, 37(5): 55～59
郑开胜,宫亚林,孙海霞,陈军伟. 箔材、薄板和中板的超声爬波检测[J]. 无损检测, 2015, 37(5): 55～59
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】北京市技术交流站.超声波探伤原理及其应用[M].北京:机械工业出版社,1984:277.
【2】蒋福堂,何双起,沈建中.兰姆波探伤中一些问题的探讨[J].材料工程,1996(10):29-31.
【3】郑开胜,刘景忠,白宝阳,等.薄板兰姆波探伤方法的评价[J].无损检测,1994,16(9): 247-248.
【4】ZHENG Kai-sheng,LIU Jing-zhong,BAI Bao-yang,et al.Evaluation on Lamb wave testing method for sheets——The Ultrasonic testing for no upside-dead zone[C]∥(Proceeding of the )6th European Conference on Non-Destructive Testing,Nice,Paris,1994,1:195-199.
【5】徐可北.兰姆波单模探伤可行性研究[C]∥中国机械工程学会无损检测学会第六届年会论文集.北京:[出版者不详],1995,111-113.
【6】张建合,徐可北.兰姆波检测技术及其应用[C]∥中国机械工程学会无损检测学会第七届年会/国际无损检测技术交流研讨会论文集.汕头:[出版者不详],1999,259-262.
【7】刘献铎.先头波及其在无损检测中的应用[J].无损检测技术,1982,3(2):14-16.
【8】ERHARD A,KRONING E.Generation,propagation,and utilisation of ultrasonic creeping wave[J].Materiaprufung,1984,26(9):323-326.
【9】ERHARD A,NUSTENBERG H.爬行波探头的特殊应用[J].国外无损检测,1985,5(3):9-13,8.
【10】郑开胜,彭应秋,陈玉成,等.粗晶TC4β挤压管的无盲区超声波检测-单晶片爬波探头的研制[J].无损检测,1999,21(8):347-349,372.
【11】ZHENG Kai-sheng,CHEN Yu-cheng,ZHANG Hong-shan.A technique of ultrasonic testing without dead zone for coarse-grained TC4β extrusion pipe—the development of single crystal creeping wave probe［C］∥7th European Conference on Non-Destructive Testing,Copenhagen:[s.n],1998(3):3064-3069.
【2】蒋福堂,何双起,沈建中.兰姆波探伤中一些问题的探讨[J].材料工程,1996(10):29-31.
【3】郑开胜,刘景忠,白宝阳,等.薄板兰姆波探伤方法的评价[J].无损检测,1994,16(9): 247-248.
【4】ZHENG Kai-sheng,LIU Jing-zhong,BAI Bao-yang,et al.Evaluation on Lamb wave testing method for sheets——The Ultrasonic testing for no upside-dead zone[C]∥(Proceeding of the )6th European Conference on Non-Destructive Testing,Nice,Paris,1994,1:195-199.
【5】徐可北.兰姆波单模探伤可行性研究[C]∥中国机械工程学会无损检测学会第六届年会论文集.北京:[出版者不详],1995,111-113.
【6】张建合,徐可北.兰姆波检测技术及其应用[C]∥中国机械工程学会无损检测学会第七届年会/国际无损检测技术交流研讨会论文集.汕头:[出版者不详],1999,259-262.
【7】刘献铎.先头波及其在无损检测中的应用[J].无损检测技术,1982,3(2):14-16.
【8】ERHARD A,KRONING E.Generation,propagation,and utilisation of ultrasonic creeping wave[J].Materiaprufung,1984,26(9):323-326.
【9】ERHARD A,NUSTENBERG H.爬行波探头的特殊应用[J].国外无损检测,1985,5(3):9-13,8.
【10】郑开胜,彭应秋,陈玉成,等.粗晶TC4β挤压管的无盲区超声波检测-单晶片爬波探头的研制[J].无损检测,1999,21(8):347-349,372.
【11】ZHENG Kai-sheng,CHEN Yu-cheng,ZHANG Hong-shan.A technique of ultrasonic testing without dead zone for coarse-grained TC4β extrusion pipe—the development of single crystal creeping wave probe［C］∥7th European Conference on Non-Destructive Testing,Copenhagen:[s.n],1998(3):3064-3069.
相关信息
