Evaluation on Measurement Uncertainty of Tensile Strength of Aluminium Alloy Based on Monte Carlo Method
摘 要
以铝合金抗拉强度为例,介绍了采用蒙特卡洛法(MCM)评定测量不确定度的步骤和方法.结果表明:采用蒙特卡洛法评定测量不确定度,无需考虑测量模型是否线性,避免了泰勒展开、求偏导数等复杂的数学推导过程,也无需将测量模型简化,可以很方便地求出标准不确定度以及给定包含概率下的扩展不确定度.
Abstract
Illustrated by the case of tensile strength test of aluminium alloy,the step and method of evaluation on measurement uncertainty based on Monte Carlo method were described.The results show that whether the measurement model is linear or not,Monte Carlo method for evaluation on measurement uncertainty was suitable.This method could easily evaluate the standard uncertainty and the expanded uncertainty of given coverage probability,without complex mathematical derivation such as Taylor expansion,seeking partial derivative for sensitivity coefficient.At the same time,it was also unnecessary to simplify measurement model.
中图分类号 TB931 DOI 10.11973/lhjy-wl201506013
所属栏目 试验与研究
基金项目 国家质检总局科技计划资助项目(2012QK131)
收稿日期 2015/2/13
修改稿日期
网络出版日期
作者单位点击查看
备注姬中华(1973-),男,高级工程师,工学硕士.
引用该论文: JI Zhong-hua,QIU Yue-long,CHENG Xiu-qin. Evaluation on Measurement Uncertainty of Tensile Strength of Aluminium Alloy Based on Monte Carlo Method[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2015, 51(6): 434~437
姬中华,邱跃龙,程秀芹. 基于蒙特卡洛法的铝合金抗拉强度测量不确定度评定[J]. 理化检验-物理分册, 2015, 51(6): 434~437
被引情况:
【1】吴 伟, "IF热轧钢板拉伸试验结果的测量不确定度评定",理化检验-物理分册 52, 392-396(2016)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】ISO/IEC GUIDE 98-3/SUPP.1Uncertainty of measurement-Part3/Supplement 1: Propagation of distributions using a Monte Carlo method[S].
【2】王承忠.测量不确定度基本原理和评定方法及在材料检测中的评定实例[J].理化检验-物理分册,2014,50(3):209-215.
【3】沈克,古兵平,唐因,等.拉伸试验测量不确定度的研究[J].武钢技术,2003,41(3):37-40.
【4】王俊,王玉玲.金属材料力学性能测试不确定度评定的探讨[J].理化检验-物理分册,2014,50(11):818-821.
【5】高波,刘杰,孙岭,等.金属材料拉伸试验结果测量不确定度评定研究[J].山东冶金,2004,26(1):54-56.
【2】王承忠.测量不确定度基本原理和评定方法及在材料检测中的评定实例[J].理化检验-物理分册,2014,50(3):209-215.
【3】沈克,古兵平,唐因,等.拉伸试验测量不确定度的研究[J].武钢技术,2003,41(3):37-40.
【4】王俊,王玉玲.金属材料力学性能测试不确定度评定的探讨[J].理化检验-物理分册,2014,50(11):818-821.
【5】高波,刘杰,孙岭,等.金属材料拉伸试验结果测量不确定度评定研究[J].山东冶金,2004,26(1):54-56.
相关信息