Effect of Preparation Processes on PTC Performance of TiB2-CB/PE Composite
摘 要
采用熔融共混法制备了TiB2-CB/PE复合材料,在130,160,180 ℃以及3,6,8 MPa的条件下热压成型后,分别进行退火处理(120,130 ℃)和硅烷交联处理,研究了热压工艺、退火温度和交联工艺对复合材料PTC性能的影响以及相关机理.结果表明:随着热压压力和温度升高,复合材料的PTC性能呈先上升再下降的趋势;在合适的热压温度和压力成型后空冷处理可以提升复合材料的结晶度,且结晶度越高,PTC性能越好;在压力为6 MPa、温度为160 ℃下热压并于空气中冷却制得复合材料的结晶度为48.4%,室温电阻率为4.47 Ω·m,PTC强度高达5.1;退火处理后,复合材料的峰值电阻率和PTC转变温度都有所提高;硅烷交联处理使复合材料的热循环稳定性得到显著提高,NTC效应也基本得以消除;复合材料PTC效应的产生与聚乙烯基体结晶区的熔融与再结晶密切相关.
Abstract
A TiB2-CB/PE composite was prepared by melt-blending process.After hot pressing molding under the conditions of temperature of 130,160,180 ℃and pressure of 3,6,8 MPa,annealing treatment(120,130 ℃) and silane crosslinking were carried out respectively.The effects of hot pressing process,annealing temperature and crosslinking process on PTC performance and PTC mechanism were investigated.The results show that PTC properties of the composite increased at first and then decreased with the increase of hot-pressing pressure and hot-pressing temperature.An appropriate hot-pressing temperature and cooling mode could increase the crystallinity of the composite,and the higher crystallinity corresponded to the more obvious PTC effect.The composite with crystallinity of 48.4%,room temperature resistivity of 4.47 Ω·m and PTC intensity of 5.1 could be obtained by hot-pressing with pressure of 6 MPa,temperature of 160 ℃ and cooling in the air.The peak resistivity and PTC transition temperature of the composite all could be increased after annealing treatment.After silane crosslinking treatment,the composite could get more stable thermal cycling property and lower NTC effect.The PTC effect of the composite was closely related to the crystallization area melting and recrystallization of polyethylene matrix.
中图分类号 TB32 TB34 DOI 10.11973/jxgccl201507016
所属栏目 材料性能及其应用
基金项目 国家重点基础研究计划(“973”计划)资助项目(2011CB013402);安徽省科技攻关计划重大项目(1301021006);安徽省教育厅自然科学重点项目(KJ2012 A232)
收稿日期 2015/1/19
修改稿日期 2015/4/14
网络出版日期
作者单位点击查看
备注施文照(1989-),男,安徽安庆人,硕士研究生.
引用该论文: SHI Wen-zhao,DU Xiao-dong,ZHAN Ma-ji,WANG Fu-cheng,LANG Jing-wei. Effect of Preparation Processes on PTC Performance of TiB2-CB/PE Composite[J]. Materials for mechancial engineering, 2015, 39(7): 77~81
施文照,杜晓东,詹马骥,王夫成,郎经纬. 制备工艺对TiB2-CB/PE复合材料PTC性能的影响[J]. 机械工程材料, 2015, 39(7): 77~81
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】张贻川,代坤,李忠明.自控温发热高分子材料研究进展[J].塑料工业,2008,36(7):6-9.
【2】宋克兴,李韶林,国秀花.TiB2含量对TiB2/Cu复合材料抗电蚀性能的影响[J].机械工程材料,2014,38(2):54-58.
【3】宋义虎,郑强,潘颐,等.单轴压力对高密度聚乙烯/碳黑导电复合材料电阻特性的影响[J].高等学校化学学报,2000,21(3):475-479.
【4】许晓秋,李景庆,张爽男,等.聚合物基PTC热敏导电材料的性能及机理研究[J].材料科学与工艺,2003,11(3):297-300.
【5】罗延龄,王庚超,张炳玉,等.热处理对聚乙烯/炭黑导电复合体系形态结构及PTC特性的影响[J].功能高分子材料,1996,9(3):329-335.
【6】周建,贾少晋,江平开,等.炭黑填充聚偏氟乙烯复合材料的PTC效应[J].高分子材料科学与工程,2011,27(7):42-45.
【7】李小慧,潘钢梁,王文东.辐照交联对聚丙烯复合材料性能的影响[J].机械工程材料,2005,29(12):56-58.
【8】益小苏,沈烈,潘颐.聚合物基导电复合材料的热敏开关特性[J].材料研究学报,2000,14(1):47-49.
【2】宋克兴,李韶林,国秀花.TiB2含量对TiB2/Cu复合材料抗电蚀性能的影响[J].机械工程材料,2014,38(2):54-58.
【3】宋义虎,郑强,潘颐,等.单轴压力对高密度聚乙烯/碳黑导电复合材料电阻特性的影响[J].高等学校化学学报,2000,21(3):475-479.
【4】许晓秋,李景庆,张爽男,等.聚合物基PTC热敏导电材料的性能及机理研究[J].材料科学与工艺,2003,11(3):297-300.
【5】罗延龄,王庚超,张炳玉,等.热处理对聚乙烯/炭黑导电复合体系形态结构及PTC特性的影响[J].功能高分子材料,1996,9(3):329-335.
【6】周建,贾少晋,江平开,等.炭黑填充聚偏氟乙烯复合材料的PTC效应[J].高分子材料科学与工程,2011,27(7):42-45.
【7】李小慧,潘钢梁,王文东.辐照交联对聚丙烯复合材料性能的影响[J].机械工程材料,2005,29(12):56-58.
【8】益小苏,沈烈,潘颐.聚合物基导电复合材料的热敏开关特性[J].材料研究学报,2000,14(1):47-49.
相关信息