Reasons Analysis and Verification on Corrosion of Plastic Panel Caused by Static Film
摘 要
某静电膜标贴(材料PVC)粘贴在除湿机注塑面板(材料HIPS)上在仓库放置数月后,注塑面板表面出现腐蚀现象.通过对静电膜标贴和注塑面板进行化学成分分析,发现静电膜标贴导致注塑面板腐蚀主要是因为静电膜标贴中的增塑剂DOP迁移至材料为HIPS的注塑面板表面并溶解于其中,从而引起注塑面板外观被破坏.同时研究表明:静电膜标贴中增塑剂DOP的迁移速率随着温度的升高而增大;且在不同的被粘贴面板上的迁移速率也不同,其中在HIPS面板表面的迁移速率最大.
Abstract
Corrosion failure was found on HIPS plastic panel of a batch of dehumidifier at the position of sticking static film after being placed to the warehouse for several months.Through analyzing chemical compositions of the plastic panel and the static film,it was found that the corrosion of the plastic panel caused by the static film was mainly due to the plasticizer DOP migrating from the static film to HIPS panel and dissolving in it.At the same time,it was found that the plasticizer DOP migrating rate was accelerated with the increase of environmental temperature,and varied on different plastic panels and achieved the maximum value on HIPS panel.
中图分类号 TQ317.2 DOI 10.11973/lhjy-wl201508014
所属栏目 试验技术与方法
基金项目
收稿日期 2014/11/3
修改稿日期
网络出版日期
作者单位点击查看
备注窦晓文(1986-),女,硕士.
引用该论文: DOU Xiao-wen. Reasons Analysis and Verification on Corrosion of Plastic Panel Caused by Static Film[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2015, 51(8): 587~589
窦晓文. 静电膜标贴导致注塑面板腐蚀原因分析及验证[J]. 理化检验-物理分册, 2015, 51(8): 587~589
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】王力,张玲,于涛,等.橡胶膨胀节开裂原因分析[J].理化检验-物理分册,2013,49(8):538-540.
【2】丛韬,付秀琴,张弘,等.铁路轮对用轴承外圈开裂失效分析[J].理化检验-物理分册,2014,50(8):599-602.
【3】王琦,贾润礼.聚氯乙烯增塑剂的研究[J].绝缘材料,2007,40(5):38-41.
【4】雍奎刚,刘忠科,刘宝钊.PVC无毒增塑剂的应用与发展[J].塑料科技,2007,35(6):88-91.
【5】石万聪,司俊杰,刘文国,等.增塑剂实用手册[M].北京:化学工业出版社,2008:524-525.
【6】冯计民.红外光谱在微量物证分析中的应用[M].北京:化学工业出版社,2010:57-59.
【7】陈金爱,马玫,苑丽红.塑料中增塑剂迁移测试方法的研究进展[J].合成材料老化与应用,2008,37(4):21-26.
【2】丛韬,付秀琴,张弘,等.铁路轮对用轴承外圈开裂失效分析[J].理化检验-物理分册,2014,50(8):599-602.
【3】王琦,贾润礼.聚氯乙烯增塑剂的研究[J].绝缘材料,2007,40(5):38-41.
【4】雍奎刚,刘忠科,刘宝钊.PVC无毒增塑剂的应用与发展[J].塑料科技,2007,35(6):88-91.
【5】石万聪,司俊杰,刘文国,等.增塑剂实用手册[M].北京:化学工业出版社,2008:524-525.
【6】冯计民.红外光谱在微量物证分析中的应用[M].北京:化学工业出版社,2010:57-59.
【7】陈金爱,马玫,苑丽红.塑料中增塑剂迁移测试方法的研究进展[J].合成材料老化与应用,2008,37(4):21-26.
相关信息