Corrosion Reasons of Produced Liquid by Polymer Flooding
摘 要
聚合物驱是油田开发中后期增产稳产的重要措施,但胜利孤东油田在实施聚合物驱后,油井管杆不同程度地出现了较水驱管杆腐蚀更加严重的问题.通过室内试验研究了聚合物驱采出液矿化度、温度、聚合物浓度、含砂量、搅拌速率、细菌含量等因素对管杆腐蚀的影响,分析了聚合物驱采出液较水驱采出液腐蚀性更强的原因.聚合物驱采出液含有的残余聚合物本身有一定的缓蚀效果,但影响不大,残余聚合物引起的采出液粘度增加、携带悬浮物的能力增强以及细菌腐蚀加重是导致聚合物驱采出液腐蚀性较重的主要原因.
Abstract
Polymer flooding is an important measure to the production stabilize and increase in the latter period of oil field development.However,after using polymer flooding,the tube wells in Gudong Oil Field exhibit more serious corrosion.The influences of salinity,temperature,polymer concentration,amount of sand,stirring rate,bacterial content of polymer flooding on corrosion rate were analyzed.The remnant polymer of polymer flooding has some corrosion inhibition effect,but with the increase of polymer content,the corrosion rate caused by polymer flooding increases,and becomes more serious than that caused by water flooding due to the increase of viscosity and capacity of suspended solids and bacteria in polymer flooding.
中图分类号 TG172
所属栏目 应用技术
基金项目 胜利油田研究课题(编号:KZD2007076)
收稿日期 2009/1/22
修改稿日期 2009/2/20
网络出版日期
作者单位点击查看
联系人作者梁伟(lwei1985@163.com)
备注梁伟,硕士研究生.
引用该论文: ZHAO Xiu-tai,LIANG Wei,QIU Guang-min,LIU De-xin,CHEN Dong-ming. Corrosion Reasons of Produced Liquid by Polymer Flooding[J]. Corrosion & Protection, 2010, 31(1): 62~64
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】顾永强,解保双,魏志高,等.孤东油田聚合物驱工业化应用的主要做法及效果[J].油气地质与采收率,2006,13(6):89-92.
【2】项名,张琦,王为.20#钢在聚丙烯酰胺驱油溶液中的腐蚀行为[J].腐蚀科学与防护技术,2005,17(3):144-147.
【3】颜廷俊,王奎升.矿化度含砂量对抽油杆油管偏磨影响及预防措施研究[J].钻采工艺,2005,28(3):93-94.
【4】陈宏,刘志庆,邹庆军.聚驱抽油机井光杆腐蚀机理及治理措施研究[J].油气田地面工程,2003,22(6):15-16.
【2】项名,张琦,王为.20#钢在聚丙烯酰胺驱油溶液中的腐蚀行为[J].腐蚀科学与防护技术,2005,17(3):144-147.
【3】颜廷俊,王奎升.矿化度含砂量对抽油杆油管偏磨影响及预防措施研究[J].钻采工艺,2005,28(3):93-94.
【4】陈宏,刘志庆,邹庆军.聚驱抽油机井光杆腐蚀机理及治理措施研究[J].油气田地面工程,2003,22(6):15-16.
相关信息