Comparison of Surface Quality of Ti5Al4V Alloys Grinded by Two Type of Grinding Wheels
摘 要
分别用SiC、CBN两种砂轮对Ti5Al4V钛合金进行了干磨削试验, 研究了在0.01, 0.03, 0.05 mm三种磨削深度下钛合金的表面硬度、表面粗糙度和表面形貌。结果表明: 随着磨削深度的增加, 经SiC砂轮磨削后, Ti5Al4V钛合金表面形貌逐渐恶化, 出现了磨削烧伤和磨削裂纹, 次表层的硬度下降, 出现了软化层; 在相同的磨削深度下, CBN砂轮磨削的Ti5Al4V钛合金表面质量优于SiC砂轮磨削的, 主要原因是CBN砂轮磨削时产生的磨削力小和磨削热较少。
Abstract
Dry grinding experiments for titanium alloy Ti5Al4V were carried out using SiC and CBN grinding wheels to study the surface micro-hardness, surface roughness and surface morphology of Ti alloy under three grinding depths (0.01, 0.03, 0.05 mm). Results show that with the increase of grinding depth, the surface morphology of the Ti5Al4V alloy grinded by SiC grinding wheel became worse, grinding burn and cracks appeared, the hardness of the subsurface decreased, and a softened layer appeared; while under the same grinding depth, the surface quality of the Ti5Al4V alloy grinded by CBN grinding wheel was superior to that by SiC grinding wheel, which was mainly attributed to CBN grinding wheel producing smaller grinding force and less heat in grinding.
中图分类号 TG74 DOI 10.11973/jxgccl201508012
所属栏目 材料性能及其应用
基金项目 安徽省自然科学基金资助项目(090414156)
收稿日期 2014/9/30
修改稿日期 2015/6/3
网络出版日期
作者单位点击查看
备注李龙(1990-), 男, 安徽阜阳人, 硕士研究生。
引用该论文: LI Long,ZHANG Xing-quan,YANG Shu-bao,WANG Shi-yi,SHI Li-ping. Comparison of Surface Quality of Ti5Al4V Alloys Grinded by Two Type of Grinding Wheels[J]. Materials for mechancial engineering, 2015, 39(8): 55~58
李龙,张兴权,杨树宝,汪世益,时礼平. 两种砂轮磨削Ti5Al4V钛合金的表面质量比较[J]. 机械工程材料, 2015, 39(8): 55~58
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】林永新, 韩传玺. 钛合金研究与工艺技术的最新进展[J]. 稀有金属材料与工程, 1994, 23(3): 74-80.
【2】朱知寿, 王新南, 童路, 等. 中国航空结构用新型钛合金研究[J].钛工业进展, 2007, 24(6): 28-32.
【3】叶伟昌. CBN砂轮的进展[J]. 新技术新工艺, 2000(11): 13-15.
【4】XU X P, YU Y P, HUANG H, et al. Mechanism of abrasive wear in the grinding of titanium(TC4) and nickel(K417) alloys[J]. Wear, 2003, 255(7): 1421-1426.
【5】刘佳, 陈五一. 杯形陶瓷CBN砂轮修整工艺及参数优化[J]. 北京航空航天大学学报, 2012, 38(3): 374-379.
【6】罗宁, 黄红武, 宓海青, 等. CBN砂轮120 m/s高速磨削表面粗糙度实验研究[J]. 精密制造与自动化, 2005(2): 22-24.
【7】YU J W, CHEN T, SHANG Z T, et al. Experimental investigation on high-speed grinding of 40Cr steel with vitrified CBN grinding wheel[J]. Advanced Materials Research, 2010, 126/128: 154-158.
【8】霍文国, 徐九华, 傅玉灿, 等. 自润滑金属结合剂CBN砂轮干式磨削特性分析[J]. 中国机械工程, 2012(23): 2773-2777.
【9】罗伟文. CBN砂轮和刚玉砂轮磨削45淬硬钢的对比试验研究[J]. 金刚石与磨料模具工程, 2005(6): 46-49.
【10】高建红, 李文辉, 刘伦伦, 等. 钛合金和镍合金加工用新型刀具材料的研究进展[J]. 机械工程材料, 2014, 38(12): 1-5.
【11】曾志新. 机械制造技术基础[M]. 武汉: 武汉理工大学出版社, 2009.
【2】朱知寿, 王新南, 童路, 等. 中国航空结构用新型钛合金研究[J].钛工业进展, 2007, 24(6): 28-32.
【3】叶伟昌. CBN砂轮的进展[J]. 新技术新工艺, 2000(11): 13-15.
【4】XU X P, YU Y P, HUANG H, et al. Mechanism of abrasive wear in the grinding of titanium(TC4) and nickel(K417) alloys[J]. Wear, 2003, 255(7): 1421-1426.
【5】刘佳, 陈五一. 杯形陶瓷CBN砂轮修整工艺及参数优化[J]. 北京航空航天大学学报, 2012, 38(3): 374-379.
【6】罗宁, 黄红武, 宓海青, 等. CBN砂轮120 m/s高速磨削表面粗糙度实验研究[J]. 精密制造与自动化, 2005(2): 22-24.
【7】YU J W, CHEN T, SHANG Z T, et al. Experimental investigation on high-speed grinding of 40Cr steel with vitrified CBN grinding wheel[J]. Advanced Materials Research, 2010, 126/128: 154-158.
【8】霍文国, 徐九华, 傅玉灿, 等. 自润滑金属结合剂CBN砂轮干式磨削特性分析[J]. 中国机械工程, 2012(23): 2773-2777.
【9】罗伟文. CBN砂轮和刚玉砂轮磨削45淬硬钢的对比试验研究[J]. 金刚石与磨料模具工程, 2005(6): 46-49.
【10】高建红, 李文辉, 刘伦伦, 等. 钛合金和镍合金加工用新型刀具材料的研究进展[J]. 机械工程材料, 2014, 38(12): 1-5.
【11】曾志新. 机械制造技术基础[M]. 武汉: 武汉理工大学出版社, 2009.
相关信息