干摩擦条件下Al2O3基复合材料的摩擦磨损特性
Friction and Wear Behaviors of Al2O3 Matrix Composites under Dry Sliding Condition
摘 要
以用SiC、Ti(CN)和ZrO2颗粒增韧的三种Al2O3基复合材料为研究对象,利用销盘式摩擦磨损试验机研究了它们的摩擦磨损性能,通过扫描电子显微镜对其磨损形貌进行了观察和分析.结果表明:在本试验条件下,Al2O3基复合材料的耐磨性能与添加剂的种类有关,其耐磨性能好坏顺序为Al2O3/Ti(CN)、Al2O3/SiC、Al2O3/ZrO2;Al2O3/SiC复合材料的磨损机理主要为疲劳磨损和脆性断裂,Al2O3/ZrO2和Al2O3/Ti(CN)复合材料的磨损机理主要为磨粒磨损.
干摩擦
磨损机理
Al2O3 matrix composite
dry friction
wear mechanism
Abstract
The friction and wear properties of three kinds of Al2O3 matrix composites strengthened by SiC,Ti(CN) and ZrO2 particles were investigated using a pin-on-disk tribometer.SEM was used to observe the friction morphology of the ceramic surface.Under this experiment conditions additives had a profound effect on the wear resistance of the composites.The sequence of wear resistance was Al2O3/ZrO2
中图分类号 TH117.1
所属栏目 材料性能及其应用
基金项目
收稿日期 2007/8/15
修改稿日期 2008/5/14
网络出版日期
作者单位点击查看
备注孟凡英(1976-),女,河北张家口人,硕士研究生.
引用该论文: MENG Fan-ying,GUO Shao-yi,LI Xing-jun,YANG Jin-lin. Friction and Wear Behaviors of Al2O3 Matrix Composites under Dry Sliding Condition[J]. Materials for mechancial engineering, 2008, 32(8): 68～70
孟凡英,郭绍义,李兴俊,杨金林. 干摩擦条件下Al2O3基复合材料的摩擦磨损特性[J]. 机械工程材料, 2008, 32(8): 68～70
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】Tarlazzi E,Roncari P,Pinasco S,et al.Tribological behaviour of Al2O3/ZrO2-ZrO2 laminated composites[J].Wear,2000,244:29-32.
【2】Bajwa S,Rainforth W M,Lee W E.Sliding wear behavior of SiC-Al2O3 nanocomposites[J].Wear,2005,259:553-561.
【3】YinY S,ShiR X,MaL P.Sintering and mechnical properties of Al2O3/TiC composites[J].International Ceramic Review,2004,53(1):24-27.
【4】兰俊思,丁培道,黄楠.SiC晶须和Ti(CN)颗粒协同增韧Al2O3陶瓷刀具的研究[J].材料科学与工程学报,2004,22(1):60-64.
【5】庞佑霞,郭源君,赵运才.不同条件下Al2O3基陶瓷材料的摩擦磨损性能研究[J].功能材料,2000,31(2):223-224.
【6】赵明,黄莉萍,丁传贤.三种结构陶瓷摩擦副的干摩擦磨损研究[J].摩擦学学报,1998,18(1):1-6.
【7】李俊宪,孙保良,邵光杰.SiC颗粒增强铝基复合材料的摩擦磨损性能[J].机械工程材料,2006,30(5):63-65.
【8】Lawn B R.A model for the wear of brittle solids under fixed abrasive condition[J].Wear,1975,33:369.
【9】肖汉宁,高朋召.高性能结构陶瓷及其应用[M].北京:化学工业出版社,2006.
【10】Evans A G,Marshall P B.Wear mechanism in ceramics proc of int conf on fundamentals[C]//Pittsburgh:ASME,1980:439-452.
【11】赵振波,刘澄,曾照强,等.过渡族金属氮化物颗粒复合氮化硅陶瓷刀具的特性[J].稀有金属材料与工程,1999,28(3):149-149.
【12】张林,范仕刚.ZrO2增韧陶瓷的研究进展[J].现代技术陶瓷,2002,23(4):23-26.
【2】Bajwa S,Rainforth W M,Lee W E.Sliding wear behavior of SiC-Al2O3 nanocomposites[J].Wear,2005,259:553-561.
【3】YinY S,ShiR X,MaL P.Sintering and mechnical properties of Al2O3/TiC composites[J].International Ceramic Review,2004,53(1):24-27.
【4】兰俊思,丁培道,黄楠.SiC晶须和Ti(CN)颗粒协同增韧Al2O3陶瓷刀具的研究[J].材料科学与工程学报,2004,22(1):60-64.
【5】庞佑霞,郭源君,赵运才.不同条件下Al2O3基陶瓷材料的摩擦磨损性能研究[J].功能材料,2000,31(2):223-224.
【6】赵明,黄莉萍,丁传贤.三种结构陶瓷摩擦副的干摩擦磨损研究[J].摩擦学学报,1998,18(1):1-6.
【7】李俊宪,孙保良,邵光杰.SiC颗粒增强铝基复合材料的摩擦磨损性能[J].机械工程材料,2006,30(5):63-65.
【8】Lawn B R.A model for the wear of brittle solids under fixed abrasive condition[J].Wear,1975,33:369.
【9】肖汉宁,高朋召.高性能结构陶瓷及其应用[M].北京:化学工业出版社,2006.
【10】Evans A G,Marshall P B.Wear mechanism in ceramics proc of int conf on fundamentals[C]//Pittsburgh:ASME,1980:439-452.
【11】赵振波,刘澄,曾照强,等.过渡族金属氮化物颗粒复合氮化硅陶瓷刀具的特性[J].稀有金属材料与工程,1999,28(3):149-149.
【12】张林,范仕刚.ZrO2增韧陶瓷的研究进展[J].现代技术陶瓷,2002,23(4):23-26.
相关信息
