Effect of Tempering Temperature on Microstructure and Mechanical Properties of As-rolled Low Carbon Baintic Steel
摘 要
对低碳贝氏体钢进行了热轧和不同温度回火处理后,采用光学显微镜和多功能材料试验机研究了回火温度对其显微组织及力学性能的影响.结果表明:不同回火温度下试验钢的显微组织主要为由板条贝氏体、粒状贝氏体、准多边形铁素体等组成的混合组织,回火温度不同,各种组织所占的比例有很大不同;回火温度对低碳贝氏体钢的屈服强度有明显影响,但对抗拉强度的影响相对较小,随着回火温度的提高,屈强比明显增加.
Abstract
A low carbon bainitic steel was hot rolled and tempered,the influence of tempering temperatures on the microstructure and mechanical properties of the steel was studied by using multi-function material testing machine and optical microscopy.The results indicate that the microstructure of the low carbon bainitic steel consisted of lath-shaped bainite,granular bainite and quasi-polygonal ferrite,and the proportion of each kind of microstructure changed with the tempering temperatures.Tempering temperatures had distinct effect on yield strength of the tested steel,and less effect on the ultimate tensile strength.The yield ratio increased with the increase of tempering temperature.
中图分类号 TG142.1
所属栏目 试验研究
基金项目 江西省自然科学基金资助项目(0605123)
收稿日期 2008/3/30
修改稿日期 2008/9/7
网络出版日期
作者单位点击查看
备注王克鲁(1968-),男,山东冠县人,副教授,博士.
引用该论文: WANG Ke-lu,LU Shi-qiang,CHEN Qing-jun,JIANG Guang-lin. Effect of Tempering Temperature on Microstructure and Mechanical Properties of As-rolled Low Carbon Baintic Steel[J]. Materials for mechancial engineering, 2009, 33(5): 9~11
王克鲁,鲁世强,陈庆军,姜广林. 回火温度对热轧低碳贝氏体钢显微组织和力学性能的影响[J]. 机械工程材料, 2009, 33(5): 9~11
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】YANG J R,HUANG C Y,WANG S C.The development of ultra-low-carbon bainitic steels[J].Materials and Design,1992(6):335-340.
【2】陈忠伟,张玉柱,杨林浩.低碳贝氏体钢的研究现状与发展前景[J].材料导报,2006,20(10):84-86.
【3】康永林,陈庆军,王克鲁,等.700 MPa级低碳贝氏体钢的热处理工艺研究[J].材料热处理学报,2005,26(3):96-99.
【4】方鸿生,刘东雨,徐平光,等.贝氏体钢的强韧化途径[J].机械工程材料,2001,25(6):1-5.
【5】王六定,朱明,陈景东,等.低碳超超高强度贝氏体钢的组织细化[J].材料热处理学报,2007,28(5):42-45.
【6】聂燚,董文龙,赵运堂,等.高强度低碳贝氏体钢工艺和组织对性能的影响[J].北京科技大学学报,2006,28(8):733-738.
【7】DEARDO A J.Multi-phase microstructures and their properties in high strength low carbon steels[J].ISIJ International,1995,35(8):946-654.
【8】尚成嘉,杨善武,王学敏,等.低碳贝氏体钢的组织类型及其对性能的影响[J].钢铁,2005,40(4):57-61.
【9】翁宇庆.超细晶钢-钢的组织细化理论与控制技术[M].北京:冶金工业出版社,2003.
【2】陈忠伟,张玉柱,杨林浩.低碳贝氏体钢的研究现状与发展前景[J].材料导报,2006,20(10):84-86.
【3】康永林,陈庆军,王克鲁,等.700 MPa级低碳贝氏体钢的热处理工艺研究[J].材料热处理学报,2005,26(3):96-99.
【4】方鸿生,刘东雨,徐平光,等.贝氏体钢的强韧化途径[J].机械工程材料,2001,25(6):1-5.
【5】王六定,朱明,陈景东,等.低碳超超高强度贝氏体钢的组织细化[J].材料热处理学报,2007,28(5):42-45.
【6】聂燚,董文龙,赵运堂,等.高强度低碳贝氏体钢工艺和组织对性能的影响[J].北京科技大学学报,2006,28(8):733-738.
【7】DEARDO A J.Multi-phase microstructures and their properties in high strength low carbon steels[J].ISIJ International,1995,35(8):946-654.
【8】尚成嘉,杨善武,王学敏,等.低碳贝氏体钢的组织类型及其对性能的影响[J].钢铁,2005,40(4):57-61.
【9】翁宇庆.超细晶钢-钢的组织细化理论与控制技术[M].北京:冶金工业出版社,2003.
相关信息