Domex700MC钢焊接接头的微动磨损性能
Fretting Wear Property of Domex 700MC Welded Joints
摘 要
采用实芯焊丝CO2气体保护焊方法焊接了低合金高强钢Domex 700MC,在无缺陷的焊态接头试样上从焊缝区、熔合区和焊接热影响区中分别截取试样进行微动磨损试验,用SEM观察了磨痕形貌.结果表明:在选定的微动磨损试验参数下,不同部位金属的磨痕面积差异较小,磨损体积和最大磨痕深度差异较大;接头不同部位金属具有不同的微动磨损性能,焊缝中心金属的耐微动磨损性最好;磨损面上存在与滑移方向成不同角度的微裂纹,这些微裂纹扩展、相交后导致金属呈块状或颗粒状脱落,所形成的凹坑有利于新的微裂纹形成.
焊接接头
微动磨损
carbon-dioxide arc welding process
welded joint
fretting wear
Abstract
The high strength low alloy steel Domex 700MC welded joints were prepared by solid wire carbon-dioxide arc welding process.The specimens for fretting wear test were cut from the sound as-welded joints at the weld zone,fusion zone and heat affected zone respectively.The fretting wear tests were carried out,and the morpholgy of the fretted wear scars were observed using SEM.The results show that under the test conditions,the plane surface area of the worn scars of the welded joints varied less,but the worn off volume and the maximum depth of the worn scars at different zone changed largely.The fretting wear properties of the welded joints at different zone were different and the weld zone metal had the best fretting wear properties.On the contacting wear interfaces,there were many micro-cracks which grew and met each other,and then led to the joint metal drop in the form of flakes or particles.The crater formed after metal drop was beneficial for forming new micro-cracks.
中图分类号 TH117.1
所属栏目 试验研究
基金项目 国家自然科学基金资助项目(50521503)
收稿日期 2008/5/25
修改稿日期 2008/11/10
网络出版日期
作者单位点击查看
备注屈金山(1958-),男,山东武城人,教授,博士研究生.
引用该论文: QU Jin-shan,ZHOU Zhong-rong. Fretting Wear Property of Domex 700MC Welded Joints[J]. Materials for mechancial engineering, 2009, 33(7): 8～11
屈金山,周仲荣. Domex700MC钢焊接接头的微动磨损性能[J]. 机械工程材料, 2009, 33(7): 8～11
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】章友谊,屈金山,王大春.高强钢Domex 700MC焊接工艺及接头性能分析[J].电焊机,2005,35(12):63-65.
【2】章友谊,屈金山,李娟,等.Domex 700MC钢性能及其焊接接头显微组织分析[J].西华大学学报,2006,25(2):80-83.
【3】周仲荣,VINCENT L.微动磨损[M].北京:科学出版社,2002:1-20.
【4】VINCENT L,BERTHIER Y,DUBOURG M C,et al.Mechanics and materials in fretting[J].Wear,1992,153(1):135-148.
【5】SAUGER E,FOUVRY S,PONSONNET L,et al.Tribologically transformed structure in fretting[J].Wear,2000,245(1/2):39-52.
【6】SAUGER E,PONSONNET L,MARTIN J M,et al.Study of the tribologically transformed structure created during fretting tests[J].Tribology International,2000,33(11):743-750.
【7】RATSIMBA C H H,MCCOLL I R,WILLIAMS E J,et al.Measurement,analysis and prediction of fretting wear damage in a representative aeroengine spline coupling[J].Wear,2004,257(11):1193-1206.
【8】HAGERJR C H,SANDERS J H,SHARMA S.Characterization of mixed and gross slip fretting wear regimes in Ti6Al4V interfaces at room temperature[J].Wear,2004,257(1/2):167-180.
【9】FOUVRY S,VINCENT L,KAPSA P.Quantification of fretting damage[J].Wear,1996,200(1/2):186-205.
【10】FOUVRY S,KAPSA P H.An energy description of hard coating wear mechanisms[J].Surface and Coatings Technology,2000,138(2/3):141-148.
【11】HUQ M Z,CELLIS J P.Expressing wear rate in sliding contacts based on dissipated energy[J].Wear,2002,252(5/6):375-383.
【12】FOUVRY S,LISKIEWICZ T,KAPSA P H,et al.An energy description of wear mechanisms and its applications to oscillating sliding contacts[J].Wear,2003,255(1/6):287-298.
【13】FOUVRY S,PAULIN C,LISKIEWICZ T.Application of an energy wear approach to quantify fretting contact durability: Introduction of a wear energy capacity concept[J].Tribo-logy International,2007,40(10/12):1428-1440.
【14】章友谊,屈金山,杨跃.Domex 700MC低合金高强度钢焊接接头显微组织分析[J].热加工工艺,2007,36(23):30-32.
【15】HONG J K,KIM I S,PARK C Y,et al.Microstructural effects on the fretting wear of Inconel 690 steam generator tube[J].Wear,2005,259(1/6):349-355.
【2】章友谊,屈金山,李娟,等.Domex 700MC钢性能及其焊接接头显微组织分析[J].西华大学学报,2006,25(2):80-83.
【3】周仲荣,VINCENT L.微动磨损[M].北京:科学出版社,2002:1-20.
【4】VINCENT L,BERTHIER Y,DUBOURG M C,et al.Mechanics and materials in fretting[J].Wear,1992,153(1):135-148.
【5】SAUGER E,FOUVRY S,PONSONNET L,et al.Tribologically transformed structure in fretting[J].Wear,2000,245(1/2):39-52.
【6】SAUGER E,PONSONNET L,MARTIN J M,et al.Study of the tribologically transformed structure created during fretting tests[J].Tribology International,2000,33(11):743-750.
【7】RATSIMBA C H H,MCCOLL I R,WILLIAMS E J,et al.Measurement,analysis and prediction of fretting wear damage in a representative aeroengine spline coupling[J].Wear,2004,257(11):1193-1206.
【8】HAGERJR C H,SANDERS J H,SHARMA S.Characterization of mixed and gross slip fretting wear regimes in Ti6Al4V interfaces at room temperature[J].Wear,2004,257(1/2):167-180.
【9】FOUVRY S,VINCENT L,KAPSA P.Quantification of fretting damage[J].Wear,1996,200(1/2):186-205.
【10】FOUVRY S,KAPSA P H.An energy description of hard coating wear mechanisms[J].Surface and Coatings Technology,2000,138(2/3):141-148.
【11】HUQ M Z,CELLIS J P.Expressing wear rate in sliding contacts based on dissipated energy[J].Wear,2002,252(5/6):375-383.
【12】FOUVRY S,LISKIEWICZ T,KAPSA P H,et al.An energy description of wear mechanisms and its applications to oscillating sliding contacts[J].Wear,2003,255(1/6):287-298.
【13】FOUVRY S,PAULIN C,LISKIEWICZ T.Application of an energy wear approach to quantify fretting contact durability: Introduction of a wear energy capacity concept[J].Tribo-logy International,2007,40(10/12):1428-1440.
【14】章友谊,屈金山,杨跃.Domex 700MC低合金高强度钢焊接接头显微组织分析[J].热加工工艺,2007,36(23):30-32.
【15】HONG J K,KIM I S,PARK C Y,et al.Microstructural effects on the fretting wear of Inconel 690 steam generator tube[J].Wear,2005,259(1/6):349-355.
相关信息
