琼脂凝胶注模成型316L不锈钢粉坯体的性能
Characteristics of 316L Stainless Steel Powders Green Body Prepared by Agar Gelcasting Technology
摘 要
以琼脂为凝胶体,用凝胶注模成型法制备了316L不锈钢粉坯体:从坯体抗弯强度、收缩率和坯体表面质量三方面析了金属粉含量、琼脂含量、分散剂含量和坯体干燥环境对坯体性能的影响.结果表明:采用金属粉含量55%(体积分数)、琼脂含量0.7%(质量分数)、分散剂含量1%(质量分数)制备坯体时,可以得到抗弯强度达2.7 MPa的坯体:置于温度、湿度可控环境中对坯体进行干燥可有效提高坯体的表面质量.
抗弯强度
收缩率
316L不锈钢
gelcasting
bending strength
shrinkage
316L stainless steel
Abstract
The green body of 316L stainless steel powders was prepared by gelcasting technology using agar as gel.The effects of metal powder content,agar content,dispersant content and dry environment of the green body on dried body propertie were investigated by the analysis of bending strength,shrinkage and surface quality of the green body.The results show that the bending strength of the green body could reach 2.7 MPa under the conditions of the metal powders content 55vol%,gel content 0.7wt% and dispersant content 1wt%.The surface quality would be improved as the green body was dried in the environment where the temperature and moisture were controllable.
中图分类号 TQ174.62
所属栏目 新材料 新工艺
基金项目 教育部科学技术研究重点资助项目(208170):国家科技支撑计划资助项目(2006BAF01A23)
收稿日期 2009/3/5
修改稿日期 2009/8/27
网络出版日期
作者单位点击查看
备注张建伟(1984-),男,山东菏泽人,硕士研究生.
引用该论文: ZHANG Jian-wei,JIANG Kai-yong,WANG Fei. Characteristics of 316L Stainless Steel Powders Green Body Prepared by Agar Gelcasting Technology[J]. Materials for mechancial engineering, 2010, 34(3): 45～47
张建伟,江开勇,王霏. 琼脂凝胶注模成型316L不锈钢粉坯体的性能[J]. 机械工程材料, 2010, 34(3): 45～47
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】KONG D Y,YANG H,WEI S,et al.Gel-casting without de-airing process using silica sol as a binder[J].Ceramics International,2007,33(2):133-139.
【2】LI Yan,GUO Zhi-meng,HAO Jun-jie.Gelcasting of 316L stainless steel[J].Journal of University of Science and Technology Beijing,2007,14(6):507-511.
【3】李艳,郭志猛,郝俊杰,等.金属粉末凝胶注模成形技术的研究现状及应用前景[J].粉末冶金工业,2006,10(16):34-37.
【4】OLHERO S M,TARI G,COIMBRA M A,et al.Synergy of polysaccharide mixtures in gelcasting of alumina[J].Journal of the European Ceramic Society,2000,20(4):423-429.
【5】MAREK P.Gelcasting of alumina foams using agarose solutions[J].Ceramics International,2008,34(3):661-667.
【6】MAREK P.Hydroxyapatite foams produced by gelcasting using agarose[J].Materials Letters,2008,62(4):1055-1057.
【7】CHEN Bi-qin,ZHANG Tao,ZHANG Jing-xian,et al.Microstructure and mechanical properties of hydroxyapatite obtained by gel-casting process[J].Ceramics International,2008,34(2):359-364.
【8】KASUHIKO S.Gel casting of metal powder for Mold SDM[D].Stanford: Stanford University,1999.
【9】潘永康,王喜忠,刘相东.现代干燥技术[M].北京:化学工业出版社,2007.
【10】JI C H,LOH N H,KHOR K A,et al.Sintering study of 316L stainless steel metal injection molding parts using Taguchi method: final density[J].Materials Science and Engineering,2001,311(1/2):74-82.
【11】王延庆.基于快速原型的金属粉浆无压浇注成型与烧结实验研究[D].济南:山东大学,2005.
【2】LI Yan,GUO Zhi-meng,HAO Jun-jie.Gelcasting of 316L stainless steel[J].Journal of University of Science and Technology Beijing,2007,14(6):507-511.
【3】李艳,郭志猛,郝俊杰,等.金属粉末凝胶注模成形技术的研究现状及应用前景[J].粉末冶金工业,2006,10(16):34-37.
【4】OLHERO S M,TARI G,COIMBRA M A,et al.Synergy of polysaccharide mixtures in gelcasting of alumina[J].Journal of the European Ceramic Society,2000,20(4):423-429.
【5】MAREK P.Gelcasting of alumina foams using agarose solutions[J].Ceramics International,2008,34(3):661-667.
【6】MAREK P.Hydroxyapatite foams produced by gelcasting using agarose[J].Materials Letters,2008,62(4):1055-1057.
【7】CHEN Bi-qin,ZHANG Tao,ZHANG Jing-xian,et al.Microstructure and mechanical properties of hydroxyapatite obtained by gel-casting process[J].Ceramics International,2008,34(2):359-364.
【8】KASUHIKO S.Gel casting of metal powder for Mold SDM[D].Stanford: Stanford University,1999.
【9】潘永康,王喜忠,刘相东.现代干燥技术[M].北京:化学工业出版社,2007.
【10】JI C H,LOH N H,KHOR K A,et al.Sintering study of 316L stainless steel metal injection molding parts using Taguchi method: final density[J].Materials Science and Engineering,2001,311(1/2):74-82.
【11】王延庆.基于快速原型的金属粉浆无压浇注成型与烧结实验研究[D].济南:山东大学,2005.
相关信息
