FCS Based High Speed Parallel Ultrasonic Signal Acquisition System
摘 要
为了实现机车、车辆和动车组等车轮的自动化在线探伤, 提出一种通过式压电超声波在线探伤方案。设计了基于FCS(现场总线控制系统)的100 MHz采样率并行超声信号采集系统。该系统充分利用车轮通过式在线探伤中顺序采样的工作特点, 采用时分复用单通道多机并行技术, 提高了高速A/D的利用率和各通道的一致性。多采样率可去除冗余数据, 提高系统的处理效率。所用缺陷信号的后续处理模式提高了缺陷定性定量识别的可靠性。
Abstract
In order to achieve the automatic online ultrasonic testing for the wheel of locomotives, vehicles and EMU, a piezoelectric transmitting-receiving online testing plan was designed. A 100MHz signal sampling rate system in parallel based on the FCS was designed. The system made full use of the order sampling characteristic and use of the parallel time-division multiplexing single-channel multi-PC technology, thus improving the utilization and consistency of the high-speed A/D channel. Sampling rate could remove many redundant datas, improve the treatment efficiency of the system. And the following up defect signals dealing mode could improve the detection reliability of the qualitative and quantitative identification.
中图分类号 TG115.28
所属栏目 仪器方法
基金项目
收稿日期 2008/9/4
修改稿日期
网络出版日期
作者单位点击查看
备注孙志林(1978-), 男, 硕士研究生, 主要研究方向为嵌入式微处理器系统的研究与设计。
引用该论文: SUN Zhi-Lin,SHI Zheng-Ying,MEI Jin-Song,BAO Ya-Ping. FCS Based High Speed Parallel Ultrasonic Signal Acquisition System[J]. Nondestructive Testing, 2009, 31(8): 639~642
孙志林,石峥映,梅劲松,包亚萍. 基于FCS的高速并行超声信号采集系统[J]. 无损检测, 2009, 31(8): 639~642
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】郭成彬, 蒋危平.认识数字超声探伤仪[J].无损检测,2004,26(3): 149-154.
【2】刘镇清, 易勇.基于数字信号处理器的超声无损检测[J].无损检测,2001,23(12): 535-537.
【3】夏继强, 邢春香.现场总线工业控制网络技术[M].北京: 北京航空航天大学出版社, 2005.
【4】Analog Device Inc. AD9054 Application Note[Z]. Analog Device Inc,2001.
【5】Xilinx Co. The Programmable Logic Data Book[Z]. Xilinx Co,2006.
【6】罗军辉, 罗勇江, 白义臣, 等.Matlab7.0在数字信号处理中的应用[M].北京: 机械工业出版社,2005.
【2】刘镇清, 易勇.基于数字信号处理器的超声无损检测[J].无损检测,2001,23(12): 535-537.
【3】夏继强, 邢春香.现场总线工业控制网络技术[M].北京: 北京航空航天大学出版社, 2005.
【4】Analog Device Inc. AD9054 Application Note[Z]. Analog Device Inc,2001.
【5】Xilinx Co. The Programmable Logic Data Book[Z]. Xilinx Co,2006.
【6】罗军辉, 罗勇江, 白义臣, 等.Matlab7.0在数字信号处理中的应用[M].北京: 机械工业出版社,2005.
相关信息