Calculation for the Blind Zone of TOFD Testing Technology and its Characteristic Analysis
摘 要
对TOFD盲区计算公式中的直通波脉冲时间宽度tp的取值进行了讨论,试验修正了公式计算结果。分析了上、下表面盲区的特性,归纳了相关影响因素。研究了焊缝型式和形状对检测盲区的影响,并使用CIVA软件进行了盲区的计算机仿真计算。
Abstract
The parameter tp (time width of through wave) of TOFD testing technique was discussed. The calculation formula was modified with the comparison testing results. Blind zone was analyzed and calculated on the characteristics of the upper and bottom surface, and the effective factors were concluded. Furthermore, the effect caused by the welding groove type and configuration on the blind zone was investigated, and the blind zone simulation was conducted in the computer by software CIVA.
中图分类号 TG115.28
所属栏目 2008远东无损检测新技术论坛优秀论文选登
基金项目
收稿日期 2008/7/10
修改稿日期
网络出版日期
作者单位点击查看
备注强天鹏(1951-),男,研究员级高级工程师,特种承压设备高级工程师,江苏省特种设备安全监督检验研究院副院长兼总工程师,长期从事无损检测和压力容器检验技术研究和工程应用。
引用该论文: QIANG Tian-Peng,XIAO Xiong,LI Zhi-Jun,ZHENG Zheng-Shun,JIANG Yun-Xi. Calculation for the Blind Zone of TOFD Testing Technology and its Characteristic Analysis[J]. Nondestructive Testing, 2008, 30(10): 738~740
强天鹏,肖雄,李智军,郑振顺,江运喜. TOFD技术的检测盲区计算和分析[J]. 无损检测, 2008, 30(10): 738~740
被引情况:
【1】牟彦春,金南辉,宋庆红, "TOFD检测技术在球形储罐检验中的应用",无损检测 33, 68-72(2011)
【2】刘礼良,郑晖,邬冠华, "超声衍射时差法检测表面盲区分析及盲区内缺陷的超声爬波检测工艺和应用",无损检测 35, 42-46(2013)
【3】孙忠波,郑红霞,张 平, "TOFD检测中借助变型波确定缺陷偏心距及缺陷精确深度的探讨",无损检测 32, 500-503(2010)
【4】肖雄,刘东梅, "非平面工件对接焊缝TOFD检测工艺",无损检测 36, 38-41(2014)
【5】郑红霞,孙忠波, "TOFD检测中扫查方式与检测盲区的关系",无损检测 33, 43-46(2011)
【6】伍卫平,范钦红,曹树林,李东风,韩志刚,倪国胜, "TOFD检测中轴偏离缺陷方位参数的测量误差",无损检测 36, 28-33(2014)
【7】伍卫平,范钦红, "一种新的TOFD检测平板对接焊缝缺陷深度的计算方法",无损检测 37, 33-37(2015)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】Tim Armitt.超声衍射时差法(TOFD)教程[Z].北京:欧宁检测技术有限公司,2007.
相关信息