Failure Analysis on a Pinion of the Jacking System of a Jack-up Platform
摘 要
通过对某自升式平台齿轮齿条升降系统的失效齿轮及全新齿条分别进行化学成分分析、金相检验和硬度测试, 分析了造成该系统中齿轮失效的原因。结果表明: 齿轮的失效形式为接触疲劳失效; 齿轮材料表面热处理不均匀, 节圆附近无硬化层, 导致其失效面的表面硬度低于与其相啮合齿条的表面硬度,这是造成该齿轮长期服役后在节圆附近发生接触疲劳失效的主要原因。
Abstract
Component analysis, metallographic examination and hardness test were performed respectively for a disabled pinion and a brand-new rack of the jacking system of a jack-up platform. The results show that because the superficial heat treatment of the pinion was not uniform, there was no hardened layer near the pitch circle of the pinion. Thus the surface hardness of the disabled pinion was lower than that of the rack, which led to the contact fatigue failure of the pinion near the pitch circle.
中图分类号 TH132.41
所属栏目 质量控制与失效分析
基金项目 中国博士后科学基金资助项目(20090461264,201003650)
收稿日期 2010/2/23
修改稿日期
网络出版日期
作者单位点击查看
备注曹宇光(1979-),男, 博士, 副教授。
引用该论文: CAO Yu-guang,ZHANG Shi-hua,LI Sen,ZHANG Qing. Failure Analysis on a Pinion of the Jacking System of a Jack-up Platform[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2010, 46(12): 806~809
曹宇光,张士华,李森,张卿. 自升式平台升降系统齿轮失效分析[J]. 理化检验-物理分册, 2010, 46(12): 806~809
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】刘桂燕,高泊依,李俊英,等. 20CrMnTi钢渗碳齿轮轴失效分析及预防措施[J]. 金属热处理,2007,32(10):95.
【2】郭志德,邵尔玉,庞钧. 齿轮的失效分析[M]. 北京:机械工业出版社,1992.
【3】MACK ALDENER M,OLSSON M. Tooth interior fatigue fracture-computational and material aspects[J]. International Journal of Fatigue,2001,23:3292340.
【4】何秀,韦先华,邓颖章,等. 装载机驱动桥主动锥齿轮失效分析及改进[J]. 装备制造技术,2007(11):128-130.
【5】张海. 20CrMnTiH钢齿轮裂纹产生机理研究[J]. 金属热处理,2000,25(12):31-33.
【6】陈乐,黄维刚,蒙秋红,等. 20CrMnTi钢齿轮表面剥落失效分析[J]. 金属热处理, 2009, 34(9):102-104.
【2】郭志德,邵尔玉,庞钧. 齿轮的失效分析[M]. 北京:机械工业出版社,1992.
【3】MACK ALDENER M,OLSSON M. Tooth interior fatigue fracture-computational and material aspects[J]. International Journal of Fatigue,2001,23:3292340.
【4】何秀,韦先华,邓颖章,等. 装载机驱动桥主动锥齿轮失效分析及改进[J]. 装备制造技术,2007(11):128-130.
【5】张海. 20CrMnTiH钢齿轮裂纹产生机理研究[J]. 金属热处理,2000,25(12):31-33.
【6】陈乐,黄维刚,蒙秋红,等. 20CrMnTi钢齿轮表面剥落失效分析[J]. 金属热处理, 2009, 34(9):102-104.
相关信息