等离子喷涂工艺参数对FeCrBSi合金涂层结合强度的影响
Effect of Plasma Spraying Process Parameters on the Bonding Strength of FeCrBSi Alloyed Coatings
摘 要
采用等离子喷涂工艺在Q235钢基体上直接制备了FeCrBSi合金涂层,使用正交试验法研究了喷涂工艺参数对涂层结合强度的影响,并对喷涂工艺参数进行了优化,同时在优化参数的基础上进一步研究了涂层厚度对结合强度的影响。结果表明：等离子喷涂制备FeCrBSi合金涂层的最佳工艺参数为喷涂电流900 A,主气流量44.8 L·min-1,辅气流量27.8 L·min-1,喷涂距离110 mm;采用最佳工艺制备的涂层与基体的结合强度为18.2 MPa,内聚强度为33.5 MPa;随着涂层厚度的增加,涂层与基体的结合强度明显下降，而涂层的内聚强度先上升后下降，较佳的涂层厚度为347.2 μm。
合金涂层
正交优化
结合强度
plasma spraying
alloyed coating
orthogonal optimization
bonding strength
Abstract
FeCrBSi alloyed coatings was prepared on Q235 steel substrate directly by plasma spraying process. The effect of plasma spraying process parameters on the bonding strength of the coatings was studied by orthogonal test method,and the process parameters were optimized at the same time. Then the effect of coating thickness on the bonding property of the coatings was also studied on the basis of optimized parameters. The results show that the best process parameters for plasma spraying FeCrBSi alloyed coatings were spraying electric current of 900 A,main gas flow of 44.8 L·min-1,assist gas flow of 27.8 L·min-1 and spraying distance of 110 mm. Bonding strength between the substrate and the coating,and inside the coating of the sample sprayed by optimized parameters was 18.2 MPa and 33.5 MPa separately. With the increase of coating thickness,bonding strength between the substrate and the coating decreased obviously,but the bonding strength inside the coating first increased and then decreased. The optimized coating thickness was 347.2 μm.
中图分类号 TB303
所属栏目 试验与研究
基金项目 江苏省自然科学基金资助项目(BK2007180)
收稿日期 2008/11/30
修改稿日期
网络出版日期
作者单位点击查看
备注殷秀银(1983-),男,硕士研究生。
引用该论文: YIN Xiu-yin,WU Yu-ping,LIN Long,WANG Tao,LU Wen-huan. Effect of Plasma Spraying Process Parameters on the Bonding Strength of FeCrBSi Alloyed Coatings[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2009, 45(8): 478～482
殷秀银,吴玉萍,林龙,王涛,卢文欢. 等离子喷涂工艺参数对FeCrBSi合金涂层结合强度的影响[J]. 理化检验－物理分册, 2009, 45(8): 478～482
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】姜银方.现代表面工程技术[M].北京：化学工业出版社,2005．
【2】张平. 热喷涂材料[M]. 北京：国防工业出版社,2006．
【3】MATSUBARA Y,TOMIGUCHI A.Surface texture and adhesive strength of high velocity oxy-fuel sprayed coatings for rolls of steel mills\[C\]// Proceedings of 13th International Thermal Spray Conference. Florida:\[s.n\],1992：637-645．
【4】胡奈赛,徐可为,何家文,等.涂镀层的结合强度评定[J].中国表面工程,1998,38(1)：31-36．
【5】吴玉萍,林萍华,王泽华,等.HVOF喷涂Fe2Cr基涂层中非晶与纳米晶形成的研究[J]. 材料热处理学报,2006(2)：15-21．
【6】段忠清,张宝霞,王泽华,等. 离子喷涂Cr2O3-8%TiO2涂层参数优化研究[J]. 表面技术,2008,37(4)：39-41．
【7】应保胜,高全杰,但斌斌,等. 离子喷涂涂层中残余应力分析[J]. 表面技术,2004,33(1)：15-17．
【2】张平. 热喷涂材料[M]. 北京：国防工业出版社,2006．
【3】MATSUBARA Y,TOMIGUCHI A.Surface texture and adhesive strength of high velocity oxy-fuel sprayed coatings for rolls of steel mills\[C\]// Proceedings of 13th International Thermal Spray Conference. Florida:\[s.n\],1992：637-645．
【4】胡奈赛,徐可为,何家文,等.涂镀层的结合强度评定[J].中国表面工程,1998,38(1)：31-36．
【5】吴玉萍,林萍华,王泽华,等.HVOF喷涂Fe2Cr基涂层中非晶与纳米晶形成的研究[J]. 材料热处理学报,2006(2)：15-21．
【6】段忠清,张宝霞,王泽华,等. 离子喷涂Cr2O3-8%TiO2涂层参数优化研究[J]. 表面技术,2008,37(4)：39-41．
【7】应保胜,高全杰,但斌斌,等. 离子喷涂涂层中残余应力分析[J]. 表面技术,2004,33(1)：15-17．
相关信息
