MICROSTRUCTURES AND MECHANICAL PROPERTIES OF THE WELDED JOINTS IN BOGIE FRAME
摘 要
采用工艺试验,力学性能试验以及光镜、电镜等显微分析等方法对转向架构架焊接接头的组织形态和力学性能进行了研究,确定了焊接接头各区的组织形态和力学性能的变化情况。研究结果表明,利用(Ar+CO2)混合气体保护焊焊接Q345E钢时,焊缝组织主要为先共析体素体、针状铁素体和珠光体,热影响区组织主要为先共析铁素体、珠光体和粒状贝氏体,焊接接头具有良好的力学性能。
Abstract
The microstructure and mechanical properties of the welding joints of bogie frame were studied through mechanical tests,optical and electron microscope observations as well as electron probe analysis etc.,then the microstructure state and variation of mechanical properties were determined. The results showed that the welded seam gotten from (Ar+CO2) gas shielded arc welding mainly contains proeutectoid ferrite,acicular ferrite and pearlite,while the heat-affected zone of which mainly contains proeutectoid ferrite,perlite and granular bainite. Tensile and impact tests combined with the hardness measurements demonstrated that the corresponding welded joints have favorable mechanical properties.
中图分类号 TG113.1 TG113.2
所属栏目 试验与研究
基金项目
收稿日期 2006/12/8
修改稿日期
网络出版日期
作者单位点击查看
备注许鸿吉(1959-),男,教授,博士。
引用该论文: XU Hong-ji,WANG Jun-jie,LI Yu-sheng,CHEN Shan-zhong,SUN Zhou-ming,LI Hua. MICROSTRUCTURES AND MECHANICAL PROPERTIES OF THE WELDED JOINTS IN BOGIE FRAME[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2007, 43(12): 599~601
许鸿吉,王君杰,李玉生,陈善忠,孙周明,李 华. 转向架构架焊接接头的组织与性能[J]. 理化检验-物理分册, 2007, 43(12): 599~601
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】丁 伟.高速列车车辆焊接转向架材质性能分析与研究[J].中国铁道科学,2001,22(2):68-72.
【2】张鑫鑫.对高速列车转向架焊接构架选材的探讨[J].机车车辆工艺,1994,14(1):41-45.
【3】吕德林.焊接金相组织[M].北京:机械工业出版社,1986:91-225.
【4】中国机械工程学会焊接学会.焊接金相图谱[M].北京:机械工业出版社,1987:74-90.
【5】李长龙,陈言俊,梁如国,等.Q345钢在低温下的力学性能研究[J].山东建筑工程学院学报,2003,18(1):82-84.
【6】陈伯蠡.焊接冶金原理[M].北京:清华大学出版社,1991:332-337.
【2】张鑫鑫.对高速列车转向架焊接构架选材的探讨[J].机车车辆工艺,1994,14(1):41-45.
【3】吕德林.焊接金相组织[M].北京:机械工业出版社,1986:91-225.
【4】中国机械工程学会焊接学会.焊接金相图谱[M].北京:机械工业出版社,1987:74-90.
【5】李长龙,陈言俊,梁如国,等.Q345钢在低温下的力学性能研究[J].山东建筑工程学院学报,2003,18(1):82-84.
【6】陈伯蠡.焊接冶金原理[M].北京:清华大学出版社,1991:332-337.
相关信息