Nondestructive Testing Method of Drilling Tool Failure
摘 要
钻具在钻井过程中的运动状态十分复杂, 长期受拉力、压力、扭矩、振动及离心力的作用, 以及钻井液的长时间腐蚀, 损伤非常严重。经反复周转使用就会出现疲劳损伤、裂纹、内外壁腐蚀、麻坑、刺穿、拉伤和切痕等缺陷, 这些缺陷如不及时检出, 将会造成钻具在井下失效, 造成经济损失。分析了钻杆失效的主要原因, 介绍了钻杆整体检测所运用的几种探伤方法。对这些方法的原理及优缺点进行了分析, 最后对钻杆整体探伤做了总结。
Abstract
In the drilling process, the motion state of drill is extremely complex. Suffering from long-standing tension, pressure, torque, vibration and centrifugal force, along with the corrosion time of drilling fluid, the damage of the drill is very serious. Through repeated usage, there are many defects will appear in the drill, such as fatigue injuries, crack, internal and external wall corrosion, pockmark, piercing, strain, and cut marks etc. If these defects were not promptly detected, failure in underground would possibly occur, resulting ingreat economic loss. The main reasons for failure of drill pipe was analyzed, and the several testing methods to detect drill pipe as a whole were also introduced. A summary of the principles, the advantages and disadvantages of final testing of the drill pipe was given.
中图分类号 TG115.28
所属栏目 实践经验
基金项目
收稿日期 2009/11/16
修改稿日期
网络出版日期
作者单位点击查看
备注王永江(1974-), 男, 工程师, 长期从事钻井工程技术和钻具管理工作, 对超声波、漏磁、荧光磁粉等无损检测工艺技术有深入研究。
引用该论文: WANG Yong-Jiang. Nondestructive Testing Method of Drilling Tool Failure[J]. Nondestructive Testing, 2010, 32(10): 810~813
王永江. 钻具失效的无损检测[J]. 无损检测, 2010, 32(10): 810~813
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】丁劲锋, 康宜华, 武新军.钻杆螺纹无损检测方法综述[J].无损检测, 2007, 26(6): 350-352.
【2】王继新.直径67 mm内丝钻杆及接头螺纹断裂分析及改进[J].探矿工程, 1995(4): 40-41.
【3】彭应秋, 朱惠, 张红波.管状螺纹连接件超声探伤方法研究[J].南昌航空工业学院学报, 1998(3): 8-13.
【4】张庆社.无磁钻具螺纹的超声波检测[J].无损检测, 2004, 26(8): 423-424.
【2】王继新.直径67 mm内丝钻杆及接头螺纹断裂分析及改进[J].探矿工程, 1995(4): 40-41.
【3】彭应秋, 朱惠, 张红波.管状螺纹连接件超声探伤方法研究[J].南昌航空工业学院学报, 1998(3): 8-13.
【4】张庆社.无磁钻具螺纹的超声波检测[J].无损检测, 2004, 26(8): 423-424.
相关信息