脉冲涡流检测信号的同步采样方法
The Synchronous Sampling on Pulsed Eddy Current Signals
摘 要
为了有效利用脉冲涡流信号的低频成分检测钢板内部裂纹缺陷, 提出了脉冲涡流同步采样方法。介绍了该方法的工作原理; 采用在钢板上加工不同规格矩形槽的方法模拟钢板的裂纹缺陷; 设计了由激励线圈和检测线圈构成的传感器, 实现脉冲涡流信号的提取; 采用数据采集卡采集信号, 以Labview为平台, 实现同步采样方法的软件设计。对钢板缺陷的检测和试验数据的分析, 证明了脉冲涡流同步采样方法在钢板内部裂纹缺陷检测中具有较高的灵敏度, 可以有效识别钢板内部裂纹缺陷。
裂纹缺陷
激励线圈
检测线圈
同步采样
Pulsed eddy current
Crack defect
Exciting coil
Measurement coil
Synchronous sampling
Abstract
In order to use the low-frequency components of the pulsed eddy current signal to detect the crack defects in the steel plate effectively, a method of pulsed eddy current synchronous sampling was proposed. The working principle of pulsed eddy current synchronous sampling method was described. Different sizes of rectangular slot in the steel plate were processed to simulate the crack defects in steel plate. A transducer consisting of exciting coil and measurement coil was designed to pick up the pulsed eddy current signal. Signal acquisition was realized by the use of Data Acquisition Card. Based on LabVIEW, the synchronous sampling software was designed. Through the steel plate defect detection and the analysis of experimental data, it was indicated that the method of pulsed eddy current synchronous sampling had a high sensitivity in steel plate internal cracks defect detection and could effectively identify defects in steel plate.
中图分类号 TG115.28
所属栏目 科研成果与学术交流
基金项目 国家自然基金仪表专项基金资助项目(60927004)
收稿日期 2009/11/17
修改稿日期
网络出版日期
作者单位点击查看
备注高松巍(1956-), 女, 教授, 主要从事无损检测技术和数字信号处理等方面的研究。
引用该论文: GAO Song-Wei,JIANG Yong-Xiang. The Synchronous Sampling on Pulsed Eddy Current Signals[J]. Nondestructive Testing, 2010, 32(11): 857～860
高松巍,蒋勇翔. 脉冲涡流检测信号的同步采样方法[J]. 无损检测, 2010, 32(11): 857～860
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】赵亮, 陈登峰, 卢英, 等.脉冲涡流在金属厚度检测中的应用研究[J].测控技术, 2007, 26(12): 22-24.
【2】叶子郁, 朱目成.应用脉冲涡流检测金属表面裂纹的研究[J].传感器技术, 2005, 24(11): 16-18.
【3】杨宾峰, 罗飞路.脉冲涡流检测系统影响因素分析[J].无损检测, 2008, 30(2): 104-106.
【4】Sophian A, Tian G Y, Taylor D, et al. A feature extraction technique based on principal component analysis for pulsed eddy current NDT[J]. NDT&E International, 2003, 36(1): 36-41.
【5】Tian G Y, Sophian A. Defect classification using a new feature for pulsed eddy current sensors[J]. NDT&E International, 2005, 38(38): 77-82.
【6】Sophian A, Tian G Y, Taylor D, et al. Design of a pulsed eddy current sensor for detection of defects in air-craft lap-joints[J]. Sensor and Actuators A: Physical, 2002(101): 92-98.
【7】Lebrun B, Jayet Y, Baboux J C. Pulsed eddy current signal analysis: application to the experimental detection and characterization of deep flaws in highly conductive materials[J]. NDT&E International, 1997, 30(3): 163-170.
【2】叶子郁, 朱目成.应用脉冲涡流检测金属表面裂纹的研究[J].传感器技术, 2005, 24(11): 16-18.
【3】杨宾峰, 罗飞路.脉冲涡流检测系统影响因素分析[J].无损检测, 2008, 30(2): 104-106.
【4】Sophian A, Tian G Y, Taylor D, et al. A feature extraction technique based on principal component analysis for pulsed eddy current NDT[J]. NDT&E International, 2003, 36(1): 36-41.
【5】Tian G Y, Sophian A. Defect classification using a new feature for pulsed eddy current sensors[J]. NDT&E International, 2005, 38(38): 77-82.
【6】Sophian A, Tian G Y, Taylor D, et al. Design of a pulsed eddy current sensor for detection of defects in air-craft lap-joints[J]. Sensor and Actuators A: Physical, 2002(101): 92-98.
【7】Lebrun B, Jayet Y, Baboux J C. Pulsed eddy current signal analysis: application to the experimental detection and characterization of deep flaws in highly conductive materials[J]. NDT&E International, 1997, 30(3): 163-170.
相关信息
