Intermediate Checks of Brinell Hardness Indentation Measuring Device
摘 要
介绍了在期间核查中,依据国标相关规定或校准规程,采用有效的布氏硬度标准块,对布氏硬度压痕测量装置读数显微镜的测量标尺和计算机中安装的压痕测量系统软件进行间接检验的方法。其检验的结果可用来判定压痕测量装置是否在校准状态,准确地了解和确认布氏硬度压痕测量装置的准确度和有效性。
Abstract
The method was introduced, by which the measuring stick of the reading microscope and the indentation measuring system software installed in the computer of Brinell hardness indentation measuring device were indirectly inspected during the intermediate checks. According to the relative national standard and calibration regulation, the method was carried out by using the valid Brinell hardness standard blocks. The inspection results could be used to determine whether the indentation measuring device was in the calibration status, and the degree of the accuracy and the effectiveness could be confirmed exactly.
中图分类号 TB938.2 DOI 10.11973/lhjy-wl201511008
所属栏目 实验室认可
基金项目
收稿日期 2015/2/4
修改稿日期
网络出版日期
作者单位点击查看
备注杜凯(1968-),女,工程师。
引用该论文: DU Kai,ZHU Li-Jun. Intermediate Checks of Brinell Hardness Indentation Measuring Device[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2015, 51(11): 784~785
杜凯,朱丽君. 布氏硬度压痕测量装置的期间核查[J]. 理化检验-物理分册, 2015, 51(11): 784~785
被引情况:
【1】王 娟,宋 芳,周利英, "CNAS-CL17《检测和校准实验室能力认可准则在玩具检测领域的应用说明》改版解读",理化检验-物理分册 52, 618-620(2016)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】李久林. 金属硬度试验方法国家标准(HB、HV、HR、HL HK、HS)实施指南[M]. 北京: 中国标准出版社,2004: 9.
【2】GB/T 231.2-2012金属材料 布氏硬度试验 第2部分: 硬度计的检验与校准[S].
【3】王承忠.万能材料试验机的期间核查[J]. 工程与试验,2010(增刊): 61-71.
【4】GB/T 231.3-2012金属材料 布氏硬度试验 第3部分: 标准硬度块的标定[S].
【5】GB/T 231.4-2009/ISO 6506-4:2014金属材料 布氏硬度试验 第4部分: 硬度值表[S].
【6】王承忠.理化检验设备和标准物质期间核查的方法及实例[J]. 理化检验-物理分册,2010,46(10): 643-649.
【2】GB/T 231.2-2012金属材料 布氏硬度试验 第2部分: 硬度计的检验与校准[S].
【3】王承忠.万能材料试验机的期间核查[J]. 工程与试验,2010(增刊): 61-71.
【4】GB/T 231.3-2012金属材料 布氏硬度试验 第3部分: 标准硬度块的标定[S].
【5】GB/T 231.4-2009/ISO 6506-4:2014金属材料 布氏硬度试验 第4部分: 硬度值表[S].
【6】王承忠.理化检验设备和标准物质期间核查的方法及实例[J]. 理化检验-物理分册,2010,46(10): 643-649.
相关信息