Forming Limit Curve for Sheet Plate Obtained by Measurement and Prediction of NADDRG Model
摘 要
利用ARAMIS动态应变测量系统测试了不同钢板的成形极限曲线(FLC),分析了钢板厚度、应变硬化指数和强度对成形极限的影响,并与NADDRG模型预测的FLC进行了对比。结果表明:钢板的成形极限应变与钢板厚度和硬化指数正相关,与强度负相关;NADDRG模型对DC系列冷轧低碳钢的FLC预测结果基本准确,但平面应变点并非试验所测FLC的最低点,试验所测FLC的最低点较平面应变点向右偏移,其主应变值与NADDRG模型预测结果一致,次应变值与各向异性塑性应变比显著负相关。
Abstract
The forming limit curves (FLC) for various steel plates were tested by ARAMIS dynamic strain measurement system, and the effects of the thickness, strain hardening exponent and strength on the forming limit were analyzed. The FLCs predicted by NADDRG model was verified and compared with experimental FLCs. The results show that forming limits of steel plates had positive correlation with the thickness and strain hardening exponent, and negative correlation with the strength. The FLCs for DC series cold-rolled steel predicted by NADDRG model were generally accurate. However, the plane strain point was not the lowest point of the experimental FLC, which shifted to the right of the plane strain point. The major strain of the experimental FLC was in accordance with the results of NADDRG model, and minor strain has significant negative correlation with anisotropic plastic strain ratio.
中图分类号 TG386.4 DOI 10.11973/jxgccl201512024
所属栏目 物理模拟与数值模拟
基金项目
收稿日期 2014/10/21
修改稿日期 2015/9/21
网络出版日期
作者单位点击查看
备注雷泽红(1973-),女,湖北武汉人,高级工程师,学士。
引用该论文: LEI Ze-hong,TU Yuan-qiang,ZHU Hong-chuan,QUAN Fang,ZHANG Wen-ying,YANG Jie. Forming Limit Curve for Sheet Plate Obtained by Measurement and Prediction of NADDRG Model[J]. Materials for mechancial engineering, 2015, 39(12): 102~106
雷泽红,涂元强,祝洪川,全 芳,张文颖,杨 杰. 板料成形极限曲线测试及NADDRG模型预测[J]. 机械工程材料, 2015, 39(12): 102~106
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】闫盖,郑燕萍,何镇罡,等. 冲压板料可成形性区域图的研究与应用[J].锻压技术, 2013,38(4):40-44.
【2】周里群,龙文宝,李玉平,等.复合镍涂层薄板成形极限应力图的理论计算[J].机械工程材料, 2013,37(10):87-91.
【3】GUVEN U. Effect of the external pressure on the plastic instability of thin-walled tubes[J]. Proceeding of the Institution of Mechanical Engineers:B,2009,223:1361-1365.
【4】胡星,杨海军.基于韧性断裂的汽车用铝合金板滚压包边成形开裂预测[J].机械工程材料, 2014,38(2):93-97.
【5】韩非,万敏,吴向东,等.板料成形极限理论与实验研究进展[J].塑性工程学报, 2006,13(5):80-84.
【6】LEVY S B. A comparison of empirical forming limit curves for low carbon steel with theoretical forming limit curves of Ramaekers and Bongaerts[C]∥IDDRG working groups meeting.[s.l.]:IDDRG,1996:140-144.
【7】于燕,车畅,赵洪运,等.成形极限曲线与板材成分及性能指标关系的探讨[J].汽车工艺与材料, 2005(4):18-23.
【2】周里群,龙文宝,李玉平,等.复合镍涂层薄板成形极限应力图的理论计算[J].机械工程材料, 2013,37(10):87-91.
【3】GUVEN U. Effect of the external pressure on the plastic instability of thin-walled tubes[J]. Proceeding of the Institution of Mechanical Engineers:B,2009,223:1361-1365.
【4】胡星,杨海军.基于韧性断裂的汽车用铝合金板滚压包边成形开裂预测[J].机械工程材料, 2014,38(2):93-97.
【5】韩非,万敏,吴向东,等.板料成形极限理论与实验研究进展[J].塑性工程学报, 2006,13(5):80-84.
【6】LEVY S B. A comparison of empirical forming limit curves for low carbon steel with theoretical forming limit curves of Ramaekers and Bongaerts[C]∥IDDRG working groups meeting.[s.l.]:IDDRG,1996:140-144.
【7】于燕,车畅,赵洪运,等.成形极限曲线与板材成分及性能指标关系的探讨[J].汽车工艺与材料, 2005(4):18-23.
相关信息