Circular Pickling and Passivation Process for Spraying System in an Icing Wind Tunnel
摘 要
为提高某结冰风洞喷雾系统使用寿命,避免雾化喷嘴在使用中发生孔径改变或堵塞,交付风洞安装前需对喷雾系统整体进行酸洗钝化。根据系统结构特性分析和耐酸性试验结果,酸洗钝化常用的浸渍法、膏剂法、喷淋法等无法用于该系统,而循环法也不适于这种末端开放式系统。经分析验证,以PU管、乳胶管替代喷雾系统中结构精密和不耐酸蚀的器件管件,用PU管、乳胶管、酸液集液管、酸液收集罐和低压耐腐蚀泵将喷雾系统组成可使酸液循环的封闭式系统。室温条件下,以硝酸、氢氟酸和Lan-826配伍为酸洗液,体积分数40%硝酸为钝化液,用循环法对系统进行了酸洗钝化,得到了合格的钝化膜。
Abstract
The pickling and passivation of spraying system is essential before it is installed in an icing wind tunnel, which would prolong the service life of spraying system and avoid dimeter variation and clogging of the nozzle in the system. The pickling and passivation process used commonly includes dipping process, pickling & passivation paste process and acid spray process. According to the structure characteristic analysis and acid test result, these processes can not be used in the spraying system. Circular pickling and passivation process seems unsuitable yet because the spraying system is an open ended system. In the final solution, latex tube and polyurethane tube were used to replace acid nonresistant devices, and an acid closed cycle system was composed of latex tubing, polyurethane tube, collector tube, acid tank and low pressure anticorrosion pump. Thus circular pickling and passivation process can be used in the spraying system. The pickling solution at room temperature was comprised of nitric acid, hydrofluoric acid and Lan-826. The passivation solution was 40vol% nitric acid. A stable passive film was obtained in such circular picking and passivation process.
中图分类号 TG178 DOI 10.11973/fsyfh-201602013
所属栏目 应用技术
基金项目
收稿日期 2015/2/7
修改稿日期
网络出版日期
作者单位点击查看
联系人作者史煜(sy403@sina.com)
备注史煜(1975-),高级工程师,本科,从事应用化学技术研究工作,
引用该论文: SHI Yu,XIAO Bin,MA Jun,JIANG Tie-deng,ZHANG Guo-biao. Circular Pickling and Passivation Process for Spraying System in an Icing Wind Tunnel[J]. Corrosion & Protection, 2016, 37(2): 147
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】刘政崇,彭强,肖斌,等. 3 m×2 m结冰风洞设计总体初步方案[C]//大型飞机关键技术高层论坛暨中国航空学会2007年学术年会论文集. 深圳:[出版者不详],2007.
【2】战培国. 结冰风洞研究综述[J]. 实验流体力学,2007,21(3): 92-96.
【3】马辉,孟繁鑫,张大林. 结冰风洞内气象参数标定方法研究[J]. 测控技术,2013,32(5): 115-120.
【4】彭强,廖达雄,肖斌,等. 结冰风洞气动设计关键技术研究[C]//第二届近代实验空气动力学会议论文集. 延吉:[出版者不详],2009.
【5】易贤,桂业伟,杜雁霞,等. 结冰风洞水滴直径标定方法研究[J]. 实验流体力学,2010,24(5): 36-41,46.
【6】范洁川,于涛. 飞机结冰风洞试验模拟研究[J]. 实验流体力学,2007,21(1): 68-72,92.
【7】王健林,陈娟华,徐建华. 不锈钢设备酸洗钝化及其质量控制技术[J]. 电站辅机,2011,32(3): 36-39.
【8】马奇. 电厂蒸汽管道安装前清洗钝化工艺的研究[D]. 长沙: 长沙理工大学,2012.
【9】孙克彬,朱瑞峰,左学兵,等. AP1000结构模块双相不锈钢腐蚀及防护[J]. 施工技术,2012,41(增1): 205-207.
【10】郭兆强. 化学品船液货舱及管线酸洗钝化[J]. 航海,2013,35(1): 62-64.
【11】李琪. 液压系统在线循环酸洗钝化技术[J]. 石油化工建设,2012,34(2): 83-84.
【12】ASTM A967-05Standard specification for chemical passivation treatments for stainless steel parts[S].
【2】战培国. 结冰风洞研究综述[J]. 实验流体力学,2007,21(3): 92-96.
【3】马辉,孟繁鑫,张大林. 结冰风洞内气象参数标定方法研究[J]. 测控技术,2013,32(5): 115-120.
【4】彭强,廖达雄,肖斌,等. 结冰风洞气动设计关键技术研究[C]//第二届近代实验空气动力学会议论文集. 延吉:[出版者不详],2009.
【5】易贤,桂业伟,杜雁霞,等. 结冰风洞水滴直径标定方法研究[J]. 实验流体力学,2010,24(5): 36-41,46.
【6】范洁川,于涛. 飞机结冰风洞试验模拟研究[J]. 实验流体力学,2007,21(1): 68-72,92.
【7】王健林,陈娟华,徐建华. 不锈钢设备酸洗钝化及其质量控制技术[J]. 电站辅机,2011,32(3): 36-39.
【8】马奇. 电厂蒸汽管道安装前清洗钝化工艺的研究[D]. 长沙: 长沙理工大学,2012.
【9】孙克彬,朱瑞峰,左学兵,等. AP1000结构模块双相不锈钢腐蚀及防护[J]. 施工技术,2012,41(增1): 205-207.
【10】郭兆强. 化学品船液货舱及管线酸洗钝化[J]. 航海,2013,35(1): 62-64.
【11】李琪. 液压系统在线循环酸洗钝化技术[J]. 石油化工建设,2012,34(2): 83-84.
【12】ASTM A967-05Standard specification for chemical passivation treatments for stainless steel parts[S].
相关信息