Pitting Corrosion Resistance of Welded Joints of 316L Lined Composite Pipe
摘 要
采用FeCl3溶液点蚀试验和点蚀电位测量,结合化学成分、显微组织分析,腐蚀形貌观察和失重试验,对采用三种工艺焊接的316L钢内衬复合管焊接接头的焊缝和热影响区的耐点蚀性能进行了研究。结果表明: 用三种焊接工艺焊接的接头耐点蚀性能依次为: 端部堆焊+625合金焊丝+钨极氩气保护焊工艺>端部封焊+625合金焊丝+钨极氩气保护焊工艺>端部封焊+药芯焊丝对焊工艺;采用端部堆焊+625合金焊丝+钨极氩气保护焊接工艺焊接的焊缝及热影响区耐点蚀性能最好。
Abstract
Pitting corrosion tests in FeCl3 solution and pitting potential measurements, chemical composition analysis, microstructure analysis, corrosion morphology observation and weight loss testing were used to study the pitting corrosion resistance of welding seams and heat affected zones in the welded joints of 316L lined composite pipes using three kinds of welding process. The results show that the order of pitting corrosion resistance of the joints welded in three kinds of welding was: end welding+625 alloy welding wire+tungsten argon shielded arc welding process> end sealing+625 alloy welding wire+tungsten argon shielded arc welding process> end sealing+flux cored wire welding process. The pitting corrosion resistance of welding seam and heat affected zone using end welding+625 alloy welding wire+tungsten argon shielded arc welding process was the best.
中图分类号 TG172 DOI 10.11973/fsyfh-201602014
所属栏目 应用技术
基金项目
收稿日期 2015/1/27
修改稿日期
网络出版日期
作者单位点击查看
备注李岩(1986),工程师,从事油田腐蚀与防护工作,
引用该论文: LI Xun-ji,LI Yan,ZHOU Li-zhi,CHANG Ze-liang,YUAN Jing,BAI Wen-tao. Pitting Corrosion Resistance of Welded Joints of 316L Lined Composite Pipe[J]. Corrosion & Protection, 2016, 37(2): 151
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】许爱华,院振刚,杨光,等. 双金属复合管的施工焊接技术[J]. 天然气与石油,2010,28(6): 22-28.
【2】朱丽霞,何小东,仝珂,等. L360QB/316L复合管电弧焊环焊缝接头组织性能研究[J]. 热加工工艺,2013,42(5): 188-190.
【3】GB/T 17897-1999不锈钢三氯化铁点腐蚀试验方法[S].
【4】孙倩,李永华,张罡,等. 304/Q235内衬式复合管焊接接头耐点蚀性研究[J]. 热加工工艺,2013,42(5): 213-215.
【5】曹楚南. 腐蚀电化学原理[M]. 北京: 化学工业出版社,1983:286-303.
【6】GB/T 17899-1999不锈钢点蚀电位测量方法[S].
【7】杨剑贇,蔡勤,葛亮亮. 316L不锈钢焊条电弧焊焊接接头组织分析[J]. 石油化工设备,2014,43(3): 24-26.
【2】朱丽霞,何小东,仝珂,等. L360QB/316L复合管电弧焊环焊缝接头组织性能研究[J]. 热加工工艺,2013,42(5): 188-190.
【3】GB/T 17897-1999不锈钢三氯化铁点腐蚀试验方法[S].
【4】孙倩,李永华,张罡,等. 304/Q235内衬式复合管焊接接头耐点蚀性研究[J]. 热加工工艺,2013,42(5): 213-215.
【5】曹楚南. 腐蚀电化学原理[M]. 北京: 化学工业出版社,1983:286-303.
【6】GB/T 17899-1999不锈钢点蚀电位测量方法[S].
【7】杨剑贇,蔡勤,葛亮亮. 316L不锈钢焊条电弧焊焊接接头组织分析[J]. 石油化工设备,2014,43(3): 24-26.
相关信息