Reasons Analysis on Unqualified Tensile Load for 10B21 Steel Tire Chains
摘 要
某厂生产的10B21钢防滑链产品抗拉载荷不合格。通过宏观检验、化学成分分析、金相检验、硬度试验和扫描电镜分析等方法对防滑链抗拉载荷不合格原因进行了分析。结果表明:该防滑链含有一定量的硼元素,淬火冷却介质温度偏高使其淬火时冷却速率不足,生成贝氏体组织,最终造成了防滑链抗拉载荷的大幅下降。
Abstract
Some tire chain products with material of 10B21 steel in a factory failed to pass the tensile test, and the unqualified reasons were analyzed by a series of testing methods including macroscopic examination, chemical composition analysis, metallographic examination, hardness test and SEM analysis. The results show that the tire chains contained a certain amount of boron element. So, if the quench cooling rate was insufficient due to the high temperature of the cooling medium, bainite structures would generate. These bainite structures would lead to a great decline in tensile load of the tire chains.
中图分类号 TG142 DOI 10.11973/lhjy-wl201604016
所属栏目 质量控制与失效分析
基金项目
收稿日期 2015/6/3
修改稿日期
网络出版日期
作者单位点击查看
备注徐 幸(1987-),男,助理工程师,硕士。
引用该论文: XU Xing. Reasons Analysis on Unqualified Tensile Load for 10B21 Steel Tire Chains[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2016, 52(4): 278~280
徐 幸. 10B21钢防滑链抗拉载荷不合格原因分析[J]. 理化检验-物理分册, 2016, 52(4): 278~280
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】王秀娟,黄洁雯,樊新民.20CrMnTi钢防滑链的质量问题与对策[J].热处理,2012,27(6): 70-72.
【2】燕样样.钢材相似显微组织的分析与鉴别[J].理化检验-物理分册,2012,48(6): 407-409.
【3】刘永飞,王平怀,党恩,等.20CrNiMo钢零件渗碳表层淬火开裂原因分析[J].理化检验-物理分册,2014,50(3): 229-231.
【4】任勇强,谢振家,尚成嘉.低碳多相钢的组织调控与力学性能[J].北京科技大学学报,2013,35(5): 592-600.
【5】洪雷,张素萍,陈继林,等.含硼冷镦钢10B21空冷工艺研究[J].河北冶金,2013(9): 1-4.
【6】董练德,陈伟庆.冷却速度对含硼冷镦钢10B21组织转变的影响[J].金属热处理,2010,35(11): 30-35.
【7】刘艳玲,孔德南,高建舟,等.硼在低碳贝氏体钢中作用的实验研究[J].河南冶金,2014,22(3): 21-24.
【2】燕样样.钢材相似显微组织的分析与鉴别[J].理化检验-物理分册,2012,48(6): 407-409.
【3】刘永飞,王平怀,党恩,等.20CrNiMo钢零件渗碳表层淬火开裂原因分析[J].理化检验-物理分册,2014,50(3): 229-231.
【4】任勇强,谢振家,尚成嘉.低碳多相钢的组织调控与力学性能[J].北京科技大学学报,2013,35(5): 592-600.
【5】洪雷,张素萍,陈继林,等.含硼冷镦钢10B21空冷工艺研究[J].河北冶金,2013(9): 1-4.
【6】董练德,陈伟庆.冷却速度对含硼冷镦钢10B21组织转变的影响[J].金属热处理,2010,35(11): 30-35.
【7】刘艳玲,孔德南,高建舟,等.硼在低碳贝氏体钢中作用的实验研究[J].河南冶金,2014,22(3): 21-24.
相关信息