Microstructure and Friction and Wear Properties of Zr-Alloyed Layer on TC4 Titanium Alloy Surface
摘 要
采用双层辉光等离子渗金属技术在TC4钛合金表面制备渗锆层, 研究了渗锆层的显微组织、相组成以及摩擦磨损性能, 并与TC4钛合金基体的摩擦磨损性能进行了对比。结果表明: TC4钛合金表面的渗锆层厚度约为10 μm; 渗锆层的组织连续、均匀、致密, 与基体结合良好, 锆含量由表层向基体内部呈梯度分布; 渗锆层的摩擦因数和比磨损率约为TC4钛合金基体的45.9%和13.6%, 摩擦磨损性能明显提高。
Abstract
Zr-alloyed layer was prepared on TC4 titanium alloy surface by using the double glow plasma alloying technique. The microstructure, phase component and friction and wear properties of the layer were studied, and the friction and wear properties of Zr-alloyed layer were compared with that of TC4 titanium alloy substrate. The results show that the thickness of Zr-alloyed layer on TC4 titaniuim alloy was about 10 μm. The Zr-alloyed layer was continuous, uniform and compact, and well combined with the substrate. The content of Zr in Zr-alloyed layer exhibited gradient distribution from the surface to substrate. The friction coefficient and specific wear rate of Zr-alloyed layer were 45.9% and 13.6% of that of TC4 titanium alloy substrate, friction and wear properties of Zr-alloyed layer was higher than that of TC4 titanium alloy substrate.
中图分类号 TF13 DOI 10.11973/jxgccl201605015
所属栏目 材料性能及其应用
基金项目 江苏省自然科学基金资助项目(BK2012463); 南京信息工程大学大学生实践创新训练计划项目(201510300209); 南京信息工程大学实验室开放课题资助项目(14KF092)
收稿日期 2015/3/8
修改稿日期 2016/1/13
网络出版日期
作者单位点击查看
备注吴红艳(1980-), 女, 河北石家庄人, 博士。
引用该论文: WU Hong-yan,ZHANG Yue-wen,HUANG Ke,TANG Xiao,GUAN Ze-han. Microstructure and Friction and Wear Properties of Zr-Alloyed Layer on TC4 Titanium Alloy Surface[J]. Materials for mechancial engineering, 2016, 40(5): 77~80
吴红艳,张跃文,黄珂,汤笑,关泽汉. TC4钛合金表面渗锆层的显微组织与摩擦磨损性能[J]. 机械工程材料, 2016, 40(5): 77~80
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】GEETHA M, SINGH A K, ASOKAMANI K, et al. Ti based biomaterials, the ultimate choice for orthopaedic implants-a review [J]. Prog Mater Sci, 2009, 54(3): 397-425.
【2】ZHU Z S, WANG X N. Research and application of aviation titanium alloys with damage tolerance [J].Materials China, 2010, 29(5): 14-17.
【3】ZHAO Y Q, QU H L, FENG L, et al. Research on high strength and high toughness TC21 alloy with damage tolerance[J].Titanium Industry Process, 2004, 21(1): 22-24.
【4】魏超, 罗勇, 强颖怀, 等. 钛合金的表面渗碳工艺及其耐磨性能[J].机械工程材料, 2008, 32(1): 35-36.
【5】徐安阳, 刘志东, 王振兴, 等. 钛合金表面柔性电极电火花强化层的组织与性能[J]. 机械工程材料, 2012, 36(2): 46-49.
【6】MAN H C , ZHANG S. Improving the wear resistance of AA 6061 by laser surface alloying with NiTi [J]. Scr Mater, 2007, 61(40): 58-61.
【7】WU H Y, ZHANG P Z, WANG L, et al. The role of process parameters in plasma surface chromising of Ti2AlNb-based alloys[J].Applied Surface Science, 2009, 256: 1333-1340.
【8】ROSSI S, FSDRIZZI L, BACCI T, et al. Corrosion behavior of glow discharge nitrided titanium alloys[J].Corrosion Science, 2003, 45: 511-529.
【9】姜爱龙, 张平则, 黄俊.TC11钛合金表面渗锆层组织及其摩擦学性能[J].机械工程材料, 2011, 35(9): 14-17.
【10】陈凯, 刘小萍, 范文娟, 等.Ti-6Al-4V 表面等离子渗锆及锆合金层的性能[J].表面技术, 2014, 43(3): 31-47.
【11】李晴宇, 杜继红, 奚正平, 等.熔盐电解制备锆合金及其反应过程研究[J].稀有金属, 2009, 33(6): 780-784.
【12】QIN L, TIAN L H, FAN A L, et al. Fatigue behavior of surface modified Ti6Al4V alloy by double glow discharge plasma alloying[J]. Surface and Coating Technology, 2007, 201: 5282-5285.
【13】SERGIY D, FRANK H, CHRISTIAN K, et al. Niobium and titanium diffusion in the high niobium-containing Ti-54Al-10Nb alloy[J]. Intermetallics, 2006, 14: 1-8.
【14】QIN L, QIN Y M, LIN X P, et al. Mechanism of enhanced wear-resistance of the Ti-Mo modification layer[J]. Materials Science Forum, 2005, 479: 3947-3950.
【15】BUDZYNSKI P, YOUSSEF A A, SIELANKO J. Surface modification of Ti-6Al-4V alloy by nitrogen ion implantation[J]. Wear, 2006, 261(11/12): 1271-1276.
【2】ZHU Z S, WANG X N. Research and application of aviation titanium alloys with damage tolerance [J].Materials China, 2010, 29(5): 14-17.
【3】ZHAO Y Q, QU H L, FENG L, et al. Research on high strength and high toughness TC21 alloy with damage tolerance[J].Titanium Industry Process, 2004, 21(1): 22-24.
【4】魏超, 罗勇, 强颖怀, 等. 钛合金的表面渗碳工艺及其耐磨性能[J].机械工程材料, 2008, 32(1): 35-36.
【5】徐安阳, 刘志东, 王振兴, 等. 钛合金表面柔性电极电火花强化层的组织与性能[J]. 机械工程材料, 2012, 36(2): 46-49.
【6】MAN H C , ZHANG S. Improving the wear resistance of AA 6061 by laser surface alloying with NiTi [J]. Scr Mater, 2007, 61(40): 58-61.
【7】WU H Y, ZHANG P Z, WANG L, et al. The role of process parameters in plasma surface chromising of Ti2AlNb-based alloys[J].Applied Surface Science, 2009, 256: 1333-1340.
【8】ROSSI S, FSDRIZZI L, BACCI T, et al. Corrosion behavior of glow discharge nitrided titanium alloys[J].Corrosion Science, 2003, 45: 511-529.
【9】姜爱龙, 张平则, 黄俊.TC11钛合金表面渗锆层组织及其摩擦学性能[J].机械工程材料, 2011, 35(9): 14-17.
【10】陈凯, 刘小萍, 范文娟, 等.Ti-6Al-4V 表面等离子渗锆及锆合金层的性能[J].表面技术, 2014, 43(3): 31-47.
【11】李晴宇, 杜继红, 奚正平, 等.熔盐电解制备锆合金及其反应过程研究[J].稀有金属, 2009, 33(6): 780-784.
【12】QIN L, TIAN L H, FAN A L, et al. Fatigue behavior of surface modified Ti6Al4V alloy by double glow discharge plasma alloying[J]. Surface and Coating Technology, 2007, 201: 5282-5285.
【13】SERGIY D, FRANK H, CHRISTIAN K, et al. Niobium and titanium diffusion in the high niobium-containing Ti-54Al-10Nb alloy[J]. Intermetallics, 2006, 14: 1-8.
【14】QIN L, QIN Y M, LIN X P, et al. Mechanism of enhanced wear-resistance of the Ti-Mo modification layer[J]. Materials Science Forum, 2005, 479: 3947-3950.
【15】BUDZYNSKI P, YOUSSEF A A, SIELANKO J. Surface modification of Ti-6Al-4V alloy by nitrogen ion implantation[J]. Wear, 2006, 261(11/12): 1271-1276.
相关信息