Friction Pair Test of Latch of Control Rod Drive Mechanism
摘 要
在三代非能动压水堆核电设备控制棒驱动机构中,钩爪材料Stellite 6合金铸件与销轴材料HS25合金、驱动杆材料12Cr13不锈钢在运行时会互相磨损,为了验证钩爪材料的磨损性能,需要对钩爪材料进行摩擦副试验。试验模拟了钩爪实际工作时的磨损情况,设计了磨损试验,通过测定磨损试块的质量损失,对钩爪材料的磨损情况进行了分析,寻找出了两种材料间的最佳摩擦副。结果表明:钩爪材料Stellite 6合金铸件与销轴材料HS25合金相匹配,且HS25合金比Stellite 6合金更适宜作为转动件;钩爪材料Stellite 6合金铸件的硬度控制在40~42 HRC较为合适。
Abstract
In generation-III passive pressurized water reactor (PWR) component control drive mechanism, the latch material Stellite 6 alloy casting, pin material HS25 alloy and drive rod material 12Cr13 stainless steel would wear each other, and in order to verify the wearing property of the latch material, friction pair test of the latch material was required. The actual wearing conditions of the latches was simulated and the friction test schemes were designed. Through measuring the mass lost of the wearing test specimens, the wearing status of the latch material was analyzed, and the best friction pairs were found. The results show that latch material Stellite 6 alloy casting was matched with pin material HS25 alloy, and HS25 alloy was more suitable to be the revolving member than Stellite 6 alloy. The hardness of latch material Stellite 6 alloy casting should be controlled in the range of 40-42 HRC.
中图分类号 TG115.5 DOI 10.11973/lhjy-wl201606005
所属栏目 试验与研究
基金项目 大型先进压水堆核电站国家科技重大专项资助项目(2010ZX06001002)
收稿日期 2016/3/14
修改稿日期
网络出版日期
作者单位点击查看
备注李 玲(1983-),女,工程师,学士,主要从事核电设备金属材料研究工作
引用该论文: LI Ling,WANG Feng,WANG Yong-dong. Friction Pair Test of Latch of Control Rod Drive Mechanism[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2016, 52(6): 384~388
李 玲,王 丰,王永东. 控制棒驱动机构钩爪摩擦副试验[J]. 理化检验-物理分册, 2016, 52(6): 384~388
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】孙汉虹,程平东,缪鸿兴,等.第三代核电技术AP1000[M].北京:中国电力出版社,2010.
【2】李荣锋.我国金属材料物理性能现场检测技术现状与展望[J].理化检验-物理分册,2015,51(12):835-838,844.
【3】周诗光.秦山一期CRDM关键部件失效机理及可靠性分析[D].上海:上海交通大学, 2008.
【4】李聪聪,曾攀,雷丽萍,等.钴基合金的滑动磨损行为及仿真预测[J].机械工程学报,2011,47(21):97-103.
【5】张晓东,董世运,徐滨士,等.St6钴基合金激光熔覆层显微组织及冲击磨料磨损性能[J].应用激光,2011,31(1):82-85.
【6】张凤林.现场布氏硬度检测技术[J].理化检验-物理分册,2015,51(12):845-852.
【7】徐扬.水润滑条件下陶瓷类复合材料摩擦学性能的研究[D].南京:南京航空航天大学, 2010.
【2】李荣锋.我国金属材料物理性能现场检测技术现状与展望[J].理化检验-物理分册,2015,51(12):835-838,844.
【3】周诗光.秦山一期CRDM关键部件失效机理及可靠性分析[D].上海:上海交通大学, 2008.
【4】李聪聪,曾攀,雷丽萍,等.钴基合金的滑动磨损行为及仿真预测[J].机械工程学报,2011,47(21):97-103.
【5】张晓东,董世运,徐滨士,等.St6钴基合金激光熔覆层显微组织及冲击磨料磨损性能[J].应用激光,2011,31(1):82-85.
【6】张凤林.现场布氏硬度检测技术[J].理化检验-物理分册,2015,51(12):845-852.
【7】徐扬.水润滑条件下陶瓷类复合材料摩擦学性能的研究[D].南京:南京航空航天大学, 2010.
相关信息