Measurement Uncertainty Evaluation on Tensile Test Results of IF Hot-rolled Steel Plate
摘 要
根据GB/T 228.1-2010《金属材料 拉伸试验 第1部分:室温试验方法》,利用WEW-600型万能材料试验机对某钢厂生产的IF热轧钢板进行了拉伸试验,分析了拉伸试验的不确定度来源,并对每个不确定度分量逐一进行了评定,最终给出了扩展不确定度及测量结果的不确定度报告。结果表明:该拉伸试验的不确定度来源主要包括试验机、量具和试验结果数据修约3个部分;当包含因子k=2时,该IF热轧钢板的下屈服强度ReL=(264±11) MPa,抗拉强度Rm=(318±13) MPa,断后伸长率A=47.5%±0.3%。该方法对金属材料拉伸试验的不确定度评定有一定的参考价值。
Abstract
According to GB/T 228.1-2010 Metallic Materials-Tensile Testing-Part 1: Method of Test at Room Temperature, tensile test was carried out on IF hot-rolled steel plate by WEW-600 universal material testing machine. The sources of uncertainty of tensile test were analyzed, every uncertainty component was evaluated, and finally the expanded uncertainty and the measurement uncertainty report were offered. The results show that the sources of uncertainty of the tensile test mainly included three aspects: testing machine, measuring tools and test results rounding. When the coverage factor k=2, the lower yield strength of the IF hot-rolled steel plate ReL=(264±11) MPa, the tensile strength Rm=(315±13) MPa, and the percentage elongation after fracture A=47.5%±0.3%. This method had certain reference value for uncertainty evaluation of tensile test for metallic materials at room temperature.
中图分类号 TG113.25 DOI 10.11973/lhjy-wl201606007
所属栏目 试验技术与方法
基金项目
收稿日期 2015/7/17
修改稿日期
网络出版日期
作者单位点击查看
备注吴 伟(1985-),男,助理工程师,主要从事金属材料力学性能检测工作
引用该论文: WU Wei. Measurement Uncertainty Evaluation on Tensile Test Results of IF Hot-rolled Steel Plate[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2016, 52(6): 392~396
吴 伟. IF热轧钢板拉伸试验结果的测量不确定度评定[J]. 理化检验-物理分册, 2016, 52(6): 392~396
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】JJF 1059.1-2012 测量不确定度评定与表示[S].
【2】GB/T 228.1-2010 金属材料 拉伸试验 第1部分:室温试验方法[S].
【3】张洪俊,陈红.K型热电偶检定过程中的测量不确定度评定[J].理化检验-物理分册, 2012,48(12):797-800.
【4】王俊,王玉玲.金属材料力学性能测试不确定度评定的探讨[J].理化检验-物理分册,2014,50(11):818-821.
【5】王承忠.测量不确定度基本原理和评定方法及在材料检测中的评定实例[J].理化检验-物理分册,2013,49(10):668-673.
【6】姬中华,邱跃龙,程秀芹.基于蒙特卡洛法的铝合金抗拉强度测量不确定度评定[J].理化检验-物理分册,2015,51(6):434-437.
【2】GB/T 228.1-2010 金属材料 拉伸试验 第1部分:室温试验方法[S].
【3】张洪俊,陈红.K型热电偶检定过程中的测量不确定度评定[J].理化检验-物理分册, 2012,48(12):797-800.
【4】王俊,王玉玲.金属材料力学性能测试不确定度评定的探讨[J].理化检验-物理分册,2014,50(11):818-821.
【5】王承忠.测量不确定度基本原理和评定方法及在材料检测中的评定实例[J].理化检验-物理分册,2013,49(10):668-673.
【6】姬中华,邱跃龙,程秀芹.基于蒙特卡洛法的铝合金抗拉强度测量不确定度评定[J].理化检验-物理分册,2015,51(6):434-437.
相关信息