Formability of B170P Cold Rolling High Strength IF Steel Plate
摘 要
高强无间隙原子(IF)钢是在IF钢基础上, 通过适当提高磷和锰含量, 得到兼具高强度和良好深冲性能的钢板,B170P钢是具有代表性的高强IF钢种之一。通过试验对B170P冷轧高强IF钢板的力学性能、显微组织、织构、成型性能等进行了全面研究, 并与深冲用DC04钢板进行了比较。结果表明: B170P钢板与DC04钢板相比, 屈服强度增加了42.86%, 抗拉强度增加了26.71%, 断后伸长率降低了6.21%, 应变硬化指数n值和塑性应变比r值基本持平; 轧面反极图和取向分布函数(ODF)图可以反映出, B170P钢板具有良好的深冲性能; B170P钢板的成型范围及膨胀性能小于DC04钢板的。
Abstract
High strengthinter stitial-free (IF) steel which was developed by appropriately increasing the phosphorus and manganese contents on the basis of IF steel, has both high tensile strength and good deep-drawing property. The B170P steel is one of the representative high strength IF steels. The mechanical properties, microstructure, texture and formability of B170P steel plate were studied comprehensively and compared with DC04 deep drawing steel plate. The results show that compared to DC04 steel plate, the yield strength of B170P steel plate increased by 42.86%, the tensile strength increased by 26.71%, the elongation after fracture decreased by 6.21%, and the strain hardening index n value and plastic strain ratio r value almost equaled. The rolling surface inverse pole figure and orientation distribution function (ODF) figure showed B170P steel plate had good deep-drawing property. The forming range and expansion property of B170P steel plate were less than those of DC04 steel plate.
中图分类号 TG386.41 DOI 10.11973/lhjy-wl201612004
所属栏目 试验与研究
基金项目
收稿日期 2016/5/4
修改稿日期
网络出版日期
作者单位点击查看
联系人作者刘红祎(aslhy@126.com)
备注刘红祎(1985-), 男, 工程师, 主要从事冷轧产品开发工作,
引用该论文: LIU Hong-yi,WANG Ya-dong,LI Xia. Formability of B170P Cold Rolling High Strength IF Steel Plate[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2016, 52(12): 851~853
刘红祎,王亚东,李霞. B170P冷轧高强IF钢板的成型性能[J]. 理化检验-物理分册, 2016, 52(12): 851~853
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】康永林.现代汽车板工艺及成形理论与技术[M].北京:冶金工业出版社,2009.
【2】李守华,李俊.汽车用高强度IF钢的研究进展[J].上海金属,2007,29(5):66-70.
【3】王利.汽车用高强度IF薄钢板[J].宝钢技术,1997(1):59-62.
【4】王斌,陈清祥,郭宾东,等.GB/T 228.1-2010 中试验方法的解读及实施[J].理化检验-物理分册,2014,50(4):251-253.
【5】苏洪英,刘菁,吕丹,等.金属材料塑性应变比r值的测试[J].理化检验-物理分册,2013,49(12):795-798.
【6】武晋,毕大森,张建,等.B180H1钢板成形性能研究[J].锻压技术,2007,32(6):64-67.
【7】王书明,王超群,樊志罡,等.织构分析在材料检测中的应用[J].理化检验-物理分册,2009,45(5):277-281.
【8】王亚芬,陈立红,李霞.烘烤硬化钢140BH组织和性能的研究[C]//第5届中国金属学会青年学术年会论文集.北京:[出版者不详],2010:247-250.
【2】李守华,李俊.汽车用高强度IF钢的研究进展[J].上海金属,2007,29(5):66-70.
【3】王利.汽车用高强度IF薄钢板[J].宝钢技术,1997(1):59-62.
【4】王斌,陈清祥,郭宾东,等.GB/T 228.1-2010 中试验方法的解读及实施[J].理化检验-物理分册,2014,50(4):251-253.
【5】苏洪英,刘菁,吕丹,等.金属材料塑性应变比r值的测试[J].理化检验-物理分册,2013,49(12):795-798.
【6】武晋,毕大森,张建,等.B180H1钢板成形性能研究[J].锻压技术,2007,32(6):64-67.
【7】王书明,王超群,樊志罡,等.织构分析在材料检测中的应用[J].理化检验-物理分册,2009,45(5):277-281.
【8】王亚芬,陈立红,李霞.烘烤硬化钢140BH组织和性能的研究[C]//第5届中国金属学会青年学术年会论文集.北京:[出版者不详],2010:247-250.
相关信息