Influence of Hot Extrusion on Microstructure and Properties of As-casted Mg-3.5Al-3.5Ca-0.6Mn Alloy
摘 要
研究了热挤压对铸态Mg-3.5Al-3.5Ca-0.6Mn合金显微组织、力学性能和耐蚀性能的影响。结果表明:热挤压能够明显细化铸态合金的组织,挤压后晶粒尺寸由80 μm减小至6 μm左右,沿晶界呈连续网状分布的粗大第二相被破碎成微米甚至纳米颗粒,并呈条带状分布于基体中;热挤压态合金的抗拉强度和伸长率分别达到313.9 MPa和9.3%,较铸态合金的分别提高了153.8%和564.3%;热挤压态合金的自腐蚀电位升高,高频容抗弧半径增大,自腐蚀电流密度和平均析氢速率下降;晶粒细化导致基体特别是晶界耐蚀性能的提高,呈条带状分布的第二相对腐蚀起到了屏障作用,晶粒细化后可形成相对稳定和致密的腐蚀产物膜,这些都是热挤压态合金耐蚀性能提高的主要原因。
Abstract
The influence of hot extrusion on the microstructure, mechanical properties and corrosion resistance of as-casted Mg-3.5Al-3.5Ca-0.6Mn alloy was investigated. The results show that hot extrusion could refine the structure of as-casted alloy with grain size from 80 μm to 6 μm after hot extrusion. The continuous network-like large second phases on grain boundaries were severely broken into micron even nanoscale particles and distributed like ribbons in the matrix. The ultimate tensile strength and elongation of hot extruded alloy were 313.9 MPa and 9.3%, which was higher than that of as cast alloy by 153.8% and 564.3%, respectively. After hot extrusion, the self-corrosion potential and arc radius of high-frequency capacity increased, while the self-corrosion current density and average hydrogen evolution rates decreased. The good corrosion resistance of matrix and grain boundaries caused by grain refinement, corrosion barrier caused by ribbon-like secondary phases and relatively stable and dense corrosion product film after grain refinement were responsible for higher corrosion resistance of hot extruded alloy.
中图分类号 TG379 DOI 10.11973/jxgccl201705007
所属栏目 试验研究
基金项目 波音(中国)投资有限公司合作课题(Agreement # 2014-SDB-14)
收稿日期 2016/2/1
修改稿日期 2017/2/1
网络出版日期
作者单位点击查看
备注张孟军(1990-),男,安徽亳州人,硕士研究生.
引用该论文: ZHANG Mengjun,XIA Weijun,CHEN Ding,WANG Xin,XIAO Di. Influence of Hot Extrusion on Microstructure and Properties of As-casted Mg-3.5Al-3.5Ca-0.6Mn Alloy[J]. Materials for mechancial engineering, 2017, 41(5): 32~37
张孟军,夏伟军,陈鼎,王新,肖迪. 热挤压对铸态Mg-3.5Al-3.5Ca-0.6Mn合金组织与性能的影响[J]. 机械工程材料, 2017, 41(5): 32~37
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】POLMEAR I J. Magnesium alloys and applications[J]. Materials Science and Technology, 1994, 10(1):1-16.
【2】陈振华, 夏伟军, 严红革,等.镁合金[M]. 北京:化学工业出版社, 2004:19-22.
【3】ZHANG L, DENG K, NIE K,et al. Microstructures and mechanical properties of Mg-Al-Ca alloys affected by Ca/Al ratio[J]. Materials Science and Engineering A, 2015, 636:279-288.
【4】KIM Y M, YIM C D, KIM H S,et al. Key factor influencing the ignition resistance of magnesium alloys at elevated temperatures[J]. Scripta Materialia, 2011, 65(11):958-961.
【5】LU Y, BRADSHAW A R, CHIU Y L,et al. Effects of secondary phase and grain size on the corrosion of biodegradable Mg-Zn-Ca alloys[J]. Materials Science and Engineering C, 2015, 48:480-486.
【6】刘子利, 丁文江. 镁铝基耐热铸造镁合金的进展[J]. 机械工程材料, 2001, 25(11):1-4.
【7】ZHANG Y, WU G, LIU W,et al. Effects of processing parameters and Ca content on microstructure and mechanical properties of squeeze casting AZ91-Ca alloys[J]. Materials Science and Engineering A, 2014, 595:109-117.
【8】KANNAN M B, RAMAN R K S. In vitro degradation and mechanical integrity of calcium-containing magnesium alloys in modified-simulated body fluid[J]. Biomaterials, 2008, 29(15):2306-2314.
【9】樊建锋, 杨根仓, 程素玲, 等. 含Ca阻燃镁合金的高温氧化行为[J].中国有色金属学报, 2004, 14(10):1666-1670.
【10】张久文, 陈荣石, 周文龙, 等. 挤压AM50(-Ca)镁合金的显微组织与力学性能研究[J]. 材料科学与工艺, 2007, 15(1):141-144.
【11】罗昊. AZ31镁合金挤压板材的力学性能和耐腐蚀性能[J]. 机械工程材料, 2013, 37(10):60-63.
【12】XU S W, OH-ISHI K, KAMADO S,et al. High-strength extruded Mg-Al-Ca-Mn alloy[J]. Scripta Materialia, 2011, 65(3):269-272.
【13】XU S W, OH-ISHI K, KAMADO S,et al. Effects of different cooling rates during two casting processes on the microstructures and mechanical properties of extruded Mg-Al-Ca-Mn alloy[J]. Materials Science and Engineering A, 2012, 542:71-78.
【14】SUZUKI A, SADDOCK N D, JONES J W,et al. Solidification paths and eutectic intermetallic phases in Mg-Al-Ca ternary alloys[J]. Acta Materialia, 2005, 53(9):2823-2834.
【15】宋佩维. 往复挤压Mg-4Al-4Si镁合金的显微组织与力学性能[J]. 中国有色金属学报, 2012, 22(7):1863-1870.
【16】ZHOU D, LIU J, ZHANG J, et al. Structural stability of intermetallic compounds of Mg-Al-Ca alloy[J]. Transactions of Nonferrous Metals Society of China, 2007, 17(2):250-256.
【17】王智祥, 谢建新, 刘雪峰, 等. 形变及时效对AZ91镁合金组织和力学性能的影响[J]. 金属学报, 2007, 43(9):920-924.
【18】樊昱, 吴国华, 高洪涛, 等. La对AZ91D镁合金力学性能和腐蚀性能的影响[J]. 金属学报, 2006, 42(1):35-40.
【19】LIU D, GUO C, CHAI L, et al. Mechanical properties and corrosion resistance of hot extruded Mg-2.5 Zn-1Ca alloy[J]. Materials Science and Engineering B, 2015, 195:50-58.
【20】AUNG N N, ZHOU W. Effect of grain size and twins on corrosion behaviour of AZ31B magnesium alloy[J]. Corrosion Science, 2010, 52(2):589-594.
【21】SONG G L, XU Z Q. The surface, microstructure and corrosion of magnesium alloy AZ31 sheet[J]. Electrochimica Acta, 2010, 55(13):4148-4161.
【2】陈振华, 夏伟军, 严红革,等.镁合金[M]. 北京:化学工业出版社, 2004:19-22.
【3】ZHANG L, DENG K, NIE K,et al. Microstructures and mechanical properties of Mg-Al-Ca alloys affected by Ca/Al ratio[J]. Materials Science and Engineering A, 2015, 636:279-288.
【4】KIM Y M, YIM C D, KIM H S,et al. Key factor influencing the ignition resistance of magnesium alloys at elevated temperatures[J]. Scripta Materialia, 2011, 65(11):958-961.
【5】LU Y, BRADSHAW A R, CHIU Y L,et al. Effects of secondary phase and grain size on the corrosion of biodegradable Mg-Zn-Ca alloys[J]. Materials Science and Engineering C, 2015, 48:480-486.
【6】刘子利, 丁文江. 镁铝基耐热铸造镁合金的进展[J]. 机械工程材料, 2001, 25(11):1-4.
【7】ZHANG Y, WU G, LIU W,et al. Effects of processing parameters and Ca content on microstructure and mechanical properties of squeeze casting AZ91-Ca alloys[J]. Materials Science and Engineering A, 2014, 595:109-117.
【8】KANNAN M B, RAMAN R K S. In vitro degradation and mechanical integrity of calcium-containing magnesium alloys in modified-simulated body fluid[J]. Biomaterials, 2008, 29(15):2306-2314.
【9】樊建锋, 杨根仓, 程素玲, 等. 含Ca阻燃镁合金的高温氧化行为[J].中国有色金属学报, 2004, 14(10):1666-1670.
【10】张久文, 陈荣石, 周文龙, 等. 挤压AM50(-Ca)镁合金的显微组织与力学性能研究[J]. 材料科学与工艺, 2007, 15(1):141-144.
【11】罗昊. AZ31镁合金挤压板材的力学性能和耐腐蚀性能[J]. 机械工程材料, 2013, 37(10):60-63.
【12】XU S W, OH-ISHI K, KAMADO S,et al. High-strength extruded Mg-Al-Ca-Mn alloy[J]. Scripta Materialia, 2011, 65(3):269-272.
【13】XU S W, OH-ISHI K, KAMADO S,et al. Effects of different cooling rates during two casting processes on the microstructures and mechanical properties of extruded Mg-Al-Ca-Mn alloy[J]. Materials Science and Engineering A, 2012, 542:71-78.
【14】SUZUKI A, SADDOCK N D, JONES J W,et al. Solidification paths and eutectic intermetallic phases in Mg-Al-Ca ternary alloys[J]. Acta Materialia, 2005, 53(9):2823-2834.
【15】宋佩维. 往复挤压Mg-4Al-4Si镁合金的显微组织与力学性能[J]. 中国有色金属学报, 2012, 22(7):1863-1870.
【16】ZHOU D, LIU J, ZHANG J, et al. Structural stability of intermetallic compounds of Mg-Al-Ca alloy[J]. Transactions of Nonferrous Metals Society of China, 2007, 17(2):250-256.
【17】王智祥, 谢建新, 刘雪峰, 等. 形变及时效对AZ91镁合金组织和力学性能的影响[J]. 金属学报, 2007, 43(9):920-924.
【18】樊昱, 吴国华, 高洪涛, 等. La对AZ91D镁合金力学性能和腐蚀性能的影响[J]. 金属学报, 2006, 42(1):35-40.
【19】LIU D, GUO C, CHAI L, et al. Mechanical properties and corrosion resistance of hot extruded Mg-2.5 Zn-1Ca alloy[J]. Materials Science and Engineering B, 2015, 195:50-58.
【20】AUNG N N, ZHOU W. Effect of grain size and twins on corrosion behaviour of AZ31B magnesium alloy[J]. Corrosion Science, 2010, 52(2):589-594.
【21】SONG G L, XU Z Q. The surface, microstructure and corrosion of magnesium alloy AZ31 sheet[J]. Electrochimica Acta, 2010, 55(13):4148-4161.
相关信息