Optimization of High Frequency Welding Procedure and Pipe Joint Properties of Heavy Wall 16Cr Stainless Steel Pipe
摘 要
通过高频焊接方法在不同工艺下焊接3.4 mm厚16Cr不锈钢板,分析了焊缝的显微组织及成形性能,并对其焊接工艺进行了优化;之后通过拉伸、压扁和扩口试验等方法研究了优化工艺下制备16Cr不锈钢焊管接头的性能。结果表明:在焊接速度10 m·min-1,焊接热输入3.0 kJ·cm-1时可获得成形性能良好的焊接接头,焊缝的组织为奥氏体和δ铁素体;制备的焊管虽然具有较高的强度,但焊缝处存在的氧化物夹杂使其韧性变差;采用适当的气体保护和避免水与高温焊缝的接触可有效地减少焊缝氧化物夹杂的产生。
Abstract
The microstructure and formability of weld for 16Cr stainless steel plate with 3.4 mm thickness by high frequency welding method in different welding parameters were studied, and the welding process was optimized. Then the properties of 16Cr stainless steel welded pipe joint under optimized process were studied by tensile test, flattening test and flaring test. The results show that welded joint with excellent formability was obtained when welding speed was 10 m·min-1 and welding heat input was 3.0 kJ·cm-1. The microstructure of weld was composed of austenite and δ-ferrite. Although the welded pipe had high strength, the toughness got worse due to the presence of oxide inclusions in the weld. The oxide inclusion in the weld could be effectively reduced by application of appropriate gas protection and avoiding high temperature weld contacted with water.
中图分类号 TG456.9 DOI 10.11973/jxgccl201707016
所属栏目 材料性能及应用
基金项目 西安石油大学《材料科学与工程》省级优势学科资助项目(ys37020203)
收稿日期 2016/3/7
修改稿日期 2017/5/15
网络出版日期
作者单位点击查看
备注毕宗岳(1962-),男,陕西宝鸡人,教授
引用该论文: BI Zongyue,YAN Peilin,WANG Haitao,YU Han. Optimization of High Frequency Welding Procedure and Pipe Joint Properties of Heavy Wall 16Cr Stainless Steel Pipe[J]. Materials for mechancial engineering, 2017, 41(7): 80~84
毕宗岳,严培林,汪海涛,余晗. 厚壁16Cr不锈钢管高频焊接工艺优化及管接头性能[J]. 机械工程材料, 2017, 41(7): 80~84
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】陈礼斌,高永春. 不锈钢技术及其发展[J]. 河北冶金,2011(3):5-12.
【2】付宏强,郜飞. 国外连续管标准简介[J]. 焊管,2015,38(2):68-72.
【3】郭志勤,蒋新.连续管钻井技术[J]. 石油钻采工艺,1999,21(1):16-20.
【4】贾凤翔. 不锈钢焊接钢管[M]. 太原:山西科学技术出版社,2007:48-56.
【5】福克哈德. 不锈钢焊接冶金[M]. 栗卓新,朱学军,译. 北京:化学工业出版社,2004:76-138.
【6】利波尔德,科特基. 不锈钢焊接冶金学及焊接性[M]. 陈剑虹,译. 北京:机械工业出版社,2008:140-159.
【7】余升旗.高频焊管常见焊接缺陷分析[J]. 焊管,2003,26(4):47-51.
【8】黄友阳. 高频焊管金属流线的形成形态与分析[J]. 钢管,2000,29(6):31-36.
【2】付宏强,郜飞. 国外连续管标准简介[J]. 焊管,2015,38(2):68-72.
【3】郭志勤,蒋新.连续管钻井技术[J]. 石油钻采工艺,1999,21(1):16-20.
【4】贾凤翔. 不锈钢焊接钢管[M]. 太原:山西科学技术出版社,2007:48-56.
【5】福克哈德. 不锈钢焊接冶金[M]. 栗卓新,朱学军,译. 北京:化学工业出版社,2004:76-138.
【6】利波尔德,科特基. 不锈钢焊接冶金学及焊接性[M]. 陈剑虹,译. 北京:机械工业出版社,2008:140-159.
【7】余升旗.高频焊管常见焊接缺陷分析[J]. 焊管,2003,26(4):47-51.
【8】黄友阳. 高频焊管金属流线的形成形态与分析[J]. 钢管,2000,29(6):31-36.
相关信息